Page 31 - Parker - Process filtration
P. 31

®
          Abso-Mate  Cartridges


          SPECIFICATIONS                      Biological Safety/Product Purity    Performance Attributes
          Materials of Construction           •  Meets USP XXI VI requirements for  Flow Rate and Pressure Drop Formulas
                                                plastics                          Flow Rate (gpm) = Clean ΔP x Length Factor
          Type of Construction                •  All components FDA listed per CFR,              Viscosity x Flow Factor
          •  Integrally sealed, all-polypropylene pleated   Title 21
            media supported by all-polypropylene   •  Non-fi ber releasing per FDA Part  Clean ΔP = Flow Rate x Viscosity x Flow Factor
            construction                        210.3B (5) and (6)                               Length Factor
                                              • Non-photo sensitive
          Filter Media                                                            Notes:
          •  Melt blown polypropylene microfi ber  Filtration Ratings              1. Clean ΔP is psi differential at start.
                                                                                  2. Viscosity is centistokes. Use Conversion Tables for other units.
                                              99.98% effi ciency at 0.2, 0.45, 1, 2, 5, 10,
          Media Support Layers                                                    3. Flow Factor is psid/gpm at 1cks for 10 in. (or single).
          •  Non-woven or mesh polypropylene  20, 40, & 70 μm pore sizes          4. Length Factors convert fl ow or ΔP from 10 in. (single length) to
                                                                                    required cartridge length.
          Media Support Core                  Beta Ratio (ß) =
          •  Heavy wall high strength polypropylene  Upstream Particle Count @ Specifi ed
                                                   Particle Size and Larger
          Media Support Cage and Thermally Welded   Downstream Particle Count @ Specifi ed
          End Caps                                 Particle Size and Larger
          • Molded polypropylene
                                              Percent Removal Effi ciency =  ß-1   100
          Seal Materials                                         ß
          •  Buna-N, EPR, Silicone, Viton , PFA   Performance determined per ASTM F-795-88. Single-Pass Test
                                  ®
                                              using AC test dust in water at a fl ow rate of 3.5gpm per 10 in.
            Encapsulated Viton ®              (13.2 lpm per 254 mm) cartridge.
                                                                                          Abso-Mate
          Dimensions                           Liquid Particle Retention Ratings (μm)                    Abso-Mate
                                                                                         Flow Factors
          Cartridge Outside Diameter           @ Removal Effi ciency of:                  (psid/gpm @ 1 cks)  Length Factors
             11
          • 2  ⁄ 16 in.                                ß=5000  ß=1000  ß=100  ß=50  ß=20  Rating  Flow   In.  Factor
                                                Cart.
          Cartridge Inside Diameter                    Absolute  99.9%  99%  98%  95%    (μm)  Factor     9     1.0
                  1
          • DOE: 1  ⁄ 16 in.                   PAB002     0.2   <0.2   <0.2  <0.2  <0.1  0.20   3.100
                  5
          • SOE: 1  ⁄ 32 in.                                                                             10     1.0
                                               PAB004    0.45    0.4    0.2  <0.2  <0.1  0.45   1.000
                                                                                                         19     2.0
          Maximum Recommended                  PAB010     1      0.8    0.4  <0.2  <0.1   1     0.750
                                                                                                         20     2.0
          Operating Conditions                 PAB020     2      1.9    0.8  <0.2  <0.1   2     0.300
                                                                                                         29     3.0
          Temperature:  200°F (93°C)           PAB050     5      3.8    1.4   0.4   0.15  5     0.072
                                                                                                         30     3.0
          Change Out ΔP:  35psi (2.4bar)       PAB100    10       7      2   0.5   0.25   10    0.031
                                                                                                         39     4.0
          ΔP @ Ambient 70°F (21°C):  90psi (6bar)  PAB200  20    13      4   1.8   0.35   20    0.021    40     4.0
          ΔP @ 200°F (93°C):  20psi (1.4bar)   PAB400    40      22      7   3.2   0.8    40    0.012
                                               PAB700    70      52     22  15     5.5    70    0.008
          Flow Rate: 10gpm (38 lpm) per 10 in. length
          Ordering Information
          PAB         —
               Filter Rating  Nominal Length  Support Construction  Seal Material  End Cap Confi guration  Special Options
              Code  Micron  Code  Inches  mm  Code  Material  Code  Material  Code  Description  Code  Description  Code  Description
               002  0.2  9  9 ⁄ 8 5  244  Glass-fi lled   Polyethylene                   SS inserted 226 O-ring/  B  Bubble-point test
                                      F  Polypropylene   P  Foam (DOE   AR  020  O-ring/Recessed cap  SSC  Closed
               004  0.45  10  9  13 ⁄16  249  (core only)  gasket only)                                     DI water rinse
                                                                DO  Double open end (DOE)  SSF  SS inserted 226 O-ring/Fin  R  (5 min.)
               010  1   19  19  5 ⁄ 8  498  304 Stainless Steel  E  EPR
                                      G                         DX  Double open end/extended core  TC  222 O-ring/Flat
               020  2   20  19  15 ⁄16  506  (core only)  N  Buna-N                                     Z6  Individual Poly
                                                                    120/120 (Filterlite LMO &               bag only
               050  5   29  29 ¼   743   Natural    S  Silicone  LL 2  Nuclepore Polymeric Vessels)  TF  222 O-ring/Fin
                                         Polypropylene
               100  10  30  30  1 ⁄16   764  A  (All support  PFA-Encap-  120 O-ring/Recessed  SS inserted 222 O-ring/
                                         components)            LR 2                 STC
               200  20  39   39  991                T 1  sulated Viton ®    (Nuclepore)  Closed
                                                       (222, 226 &
               400  40  40   40   1016                 O-ring only)*  OB  Std. open end/Polypropylene  STF  SS inserted 222 O-ring/Fin
                                                                    spring closed end
               700  70                              V  Viton ®
                                                                PR 2  213 O-ring/Recessed cap (Ametek ®    TX  222 O-ring/Flex Fin
                                                       No seal      & Parker LT Polymeric Vessels)
                                                    X
                                                       material
                                                                SC  226 O-ring/Flat      Ext. core open end/
                                                  1 PFA/Viton is O-ring               XB  Polypropylene spring
                                                                SF  226 O-ring/Fin       closed end
                                                  only, T is expanded
                                                  PTFE gaskets  2 Available only in 9  5 ⁄ 8 ˝ (-9) and 19  5 ⁄ 8 ˝ (-10) lengths
          Specifi cations are subject to change without notifi cation.                           © 2010 Parker-Hannifi n Corporation
          For User Responsibility Statement, see www.parker.com/safety                    domnick hunter Process Filtration - North America
                                                                                                          All Rights Reserved
                                                                                     Fulfl o is a registered trademark of Parker-Hannifi n Corporation
                                                                                 Viton is a registered trademark of E.I. DuPont de Nemours & Co., Inc.
                                                                                            Ametek is a registered trademark of Ametek, Inc.
                                                                                                       DS_IP_Abso-Mate  Rev. A
                                                             31
   26   27   28   29   30   31   32   33   34   35   36