Page 89 - Parker - Process filtration

®
™
Fulfl o TruBind 300 Filter Cartridge
SPECIFICATIONS
Materials of Construction Recommended Vessels: Performance
Absorbent: Proprietary modifi ed polymer All standard Fulfl o vessels designed for TruBind absorbent cartridge effi ciency
Support Construction: 100% polyolefi n 2-1/2 in OD cartridges. depends upon the residence time of the
Seal Material: Gasket (Polyethylene Foam); fl uid within the cartridge, which is a function
Technology
222 O-Ring (Buna-N) of the volumetric fl ow rate.
Unlike competitive technologies in which 1. Hydrocarbon Removal Effi ciency: At
Maximum Recommended hydrocarbons are removed through surface an equivalent fl ow rate of 1.0gpm per
Operating Conditions adsorption onto the medium, TruBind 10-inch cartridge the TruBind cartridge
Temperature: cartridges utilize a proprietary modifi ed typically reduces trace hydrocarbon
150°F (65°C) @ 20psid (1.4bar); 180°F polymer that both absorbs and chemically contaminant in excess of 95% in
(82°C) @10psid (0.7bar) binds the hydrocarbon molecules into single pass mode. This effi ciency
Pressure: its interior matrices. The affi nity of the level can be maintained only to a net
40psid (2.8bar) @ 75°F (24°C) polymeric absorbent for hydrocarbon differential pressure of 10psi. Series or
Flow Rate: contaminant is so great that accelerated multipass fi ltration can virtually eliminate
1.0gpm per 10-inch cartridge testing by the Toxic Characteristics hydrocarbon contamination.
Change-out Pressure Drop (net): Leachate Procedure (TCLP) indicated the 2. Hydrocarbon Absorbent Capacity:
10psi (0.7bar) effl uent hydrocarbon level in water to be The TruBind cartridge medium has the
Flow Factor: below current and proposed EPA limits. potential to remove up to 250 grams
0.03psid per 1gpm at 1cks viscosity per The modifi ed polymer was formulated (approximately one-half pint) of low
10 in cartridge to control the speed of hydrocarbon density hydrocarbon contaminant. On
pH Range: 2 - 12 absorption by eliminating the potential for this basis, the table below provides
Lengths: 10-40 in (249mm-1016mm) skin formation at the polymer/hydrocarbon expected life data in hours orgallons
interface. Consequently this polymer, when
Dimensions: incorporated into a radial-fl ow-design at several trace contaminant levels
Outside Diameter: 2½˝ in (63.5 mm) cartridge, insures maximum utilization of based on a 1.0gpm fl ow rate per 10-
1 ˝
Inside Diameter: 1 ⁄ 16 in (27 mm) surface area. The nature of the polymer inch cartridge. Absorbent capacity will
decrease as density of hydrocarbon
makes it an effective absorbent for free,
Bio-safety: increases.
The TruBind cartridge is classifi ed as non- emulsifi ed and dissolved oils, synthetic 3. Flow Rate Capability: A maximum fl ow
hazardous and incinerable. Disposal must lubricants, grease and a multitude of rate of 1.0gpm per 10-inch length
organic solvents.
be dictated by local regulations pertaining cartridge is recommended for the most
to the absorbed contaminant. effective removal of trace hydrocarbon
contaminant.
Estimated Use the following equations
Hydrocarbon
Hydrocarbon Concentration removal per Estimated life Gallons fl uid cost per to calculate performance:
(ppm) % by weight in hours treated gallon of Life (Hrs.) = 1100.8/PPM
minute (grams) Removal Rate (Grams/Min)
treated fl uid
= PPM/264.2
10 .001 0.04 106.0 6,330 $.003
100 .01 .40 10.6 633 $.03
1,000 .1 4.00 1.1 63 $.30
Note: Cost per gallon decreases signifi cantly with longer cartridges.

Ordering Information
TBC

Cartridge Series Length Support Core (QG &DS &RQ¿JXUDWLRQ Seal Material
TruBind Absorbent FRGH LQ PP A = Standard Wall DO = Double-Open-End A 3RO\ROH¿Q )RDP *DVNHW
Cartridge ǫÝ Polypropylene Core JDVNHW VHDO (standard for “DO” seal design)
10 9 13 » 16Ý
ǫÝ DX = DOE w/core extender N = Buna-N O-Ring
20 19 15 » 16Ý TC = Single-Open-End (standard for “TC” seal design)
óÝ (222 O-ring seal)
30 30 » 16Ý 7; 2 ULQJ )OH[ )LQ
1
39 39 991

Specifi cations are subject to change without notifi cation. © 2010 Parker-Hannifi n Corporation
For User Responsibility Statement, see www.parker.com/safety domnick hunter Process Filtration - North America
All Rights Reserved
Fulfl o is a registered trademark of Parker-Hannifi n Corporation
DS_IP_TruBind 300 Rev. A

89