Page 3 - QR IMER COMBI-250VA

IMER INTERNATIONAL S.p.A. GB
COMBI 250 VA

Dear Customer, Feature European motor European motor
Congratulations on your choice of purchase: IMER saws are
the result of years of experience and are equipped with all the Power (kW) (230V/50Hz ) (110V/50Hz )
Rated voltage (V)
latesttechnicalinnovations. 1.1 1.1
Frequency (Hz)
- WORKING IN SAFETY. Absorbed current 230 110
Number of poles
To work in complete safety, read the following instructions 50 50
carefully before using the machine. rpm
Service type 7.8 15.4
To work in complete safety, read the following instructions Insulation category
carefully before using the machine. Protection category 22
This OPERATION AND MAINTENANCE manual must be kept on Capacitor (µF)
site by the person in charge, e.g. the SITE FOREMAN, and 2800 2800
must always be available for consultation.
The manual is to be considered integral part of the machine S6 40% S6 40%
and must be kept for future reference (EN 12100/2) until the
machine is disposed of. If the manual is damaged or lost, a FF
replacement may be requested from the manufacturer.
The manual contains important information regarding site IP 5 5 IP 5 5
preparation, machine use, maintenance procedures, and
requests for spare parts. 25(Ø 40x92) 90(Ø 50x120)
Nevertheless, the installer and the operator must both have
adequate experience and knowledge of the machine prior to 2. DESIGN STANDARDS
use. COMBI 250 saws have been designed and manufactured
To guarantee complete safety of the operator, safe operation according to the following standards: EN 12100-1-2; EN
and long life of equipment, follow the instructions in this 60204-1;EN 12418.
manual carefully, and observe all safety standards currently in
force for the prevention of accidents at work (use of safety 3. SOUND PRESSURE LEVEL AND VIBRATIONS
footwear and suitable clothing, helmets, gloves, goggles etc.). Table 3 shows the sound pressure level measured loadless at
the operator s ear (LPA) and of the vibrations transmitted during
- Make sure that all signs are legible. operation.

- It is strictly forbidden to carry out any form of TABLE 3
modification to the steel structure or working parts of
the machine. SAWING MACHINE TYPE OF MOTOR LpA Aeq
86 dB 2.57 m/s2
IMER INTERNATIONAL declines all responsibility for failure to Combi 250 VA ELECTRIC
comply with laws and standards governing the use of this
equipment, in particular; improper use, defective power 4. GENERAL SAW DESCRIPTION
supply, lack of maintenance, unauthorised modifications, and
partial or total failure to observe the instructions contained in 4.1 General description:
this manual.
IMER INTERNATIONAL reserves the right to modify features of The Combi 250 VA is a saw comprising the following main
the saw and contents of this manual, without the obligation to sub-groups :
update previous machines and/or manuals. - cutting head (ref. A fig.1).
- sliding guide (ref. B fig.1).
1. TECHNICAL DATA - water collection tank (ref. C fig.1).
Technical data are stated in table 1 and electrical - cutting surface (ref. F fig.2).
specifications in table 2. - stand (ref. G fig.5).
- power cable.
TECHNICAL DATA - Table 1 The cutting head is mounted on a reinforced aluminium profile
and is equipped with horizontal and vertical movement
Model COMBI 250 VA facilities. The aluminium profile is hinged onto die-cast arms
(ref.H fig. 5) and the entire unit can rotate through 45° ( fig. 6)
Max. blade diameter 250 mm by means of the relative handwheels (ref.L fig. 7).
The cutting surfaces are positioned on the tubular frame of the
Diamond Blade hole diameter 25.4 mm saw which is placed on the tank constructed in impact-
Single phase 230 V 50 Hz motor power 1.1 kW resistant plastic.
Single phase 110 V 50 Hz motor power 1.1 kW The water immersion pump is mounted below the cutting
Max. blade rotation speed (230 V 50 HZ) 2800 rpm surfaces on a special bracket and supplies a water distributor
Max. blade rotation speed (110 V 50 HZ) 2800 rpm inside the blade guard for cooling the cutting blade during
Cutting table dimensions 850x500 mm operation.
Length of 90° cuts (thickness=16mm) 660 mm The high resistance plastic handle (ref.M fig. 6), is equipped
Length of cuts from above 785 mm with the main ON-OFF switch on the operator side to facilitate
Maximum cut depth with single stroke 66 mm saw activation and shutdown.The raised position of the red
Maximum cut depth with two stroke 105 mm OFF button on the handle is designed to facilitate shutdown of
Water pump flow rate 13 l/min the machine in the event of an emergency. The motor
capacitor is located in a protected position inside the handle.
Water tank capacity 36 L The saw is fitted with a guard to guarantee optimal safety
during operation and to protect the user during cutting cycles.
Machine dimensions 1050x565x480 A valve is mounted above the blade guard to adjust the flow
rate of water delivered to the cutting blade.
Packed machine dimensions 1090x610x525 mm
4.2 Processable materials:
Weight with packaging 43 kg This saw has been designed for cutting the following
materials: ceramic tiles, masonry and stone in general with
maximum dimensions compatible with the length, cutting depth
and dimensions of the surfaces specified in Table 1.
Maximum weight of processable materials: 25 kg.

10