Page 2 - Area 51 CDs

03.29.2023

1 2) GENERAL CONTRACTOR IS RESPONSIBLE TO COMPLY WITH ALL APPLICABLE CODES, MUNICIPAL ORDINANCES, AND BUILDING 3) THE CONTRACTOR SHALL INVESTIGATE ALL FIELD CONDITIONS AND SHALL PROMPTLY NOTIFY THE ARCHITECT OF ANY WHICH DO NOT AGREE WITH THOSE SHOWN IN THESE DRAWINGS. WORK AFFECTED BY DISCREPANCIES SHALL CEASE UNTIL THEY ARE 4) ALL SUBSTITUTIONS AND CHANGES TO THESE DRAWINGS MUST BE SUBMITTED TO THE ARCHITECT AND / OR OWNER FOR SUBCONTRACTORS ARE RESPONSIBLE TO OBTAIN ALL REQUIRED BUILDING PERMITS AND LICENSES AS REQUIRED BY THE MUNICIPALITY TO PERFORM CONSTRUCTION ACTIVITIES REQUIRED 6) THE CONTRACTOR SHALL BE HELD ENTIRELY RESPONSIBLE FOR SAFETY REGULATIONS, PROCEDURES AND POLICIES. 7) THIS WORK IS PRIMARILY FOR BUILDING PERMIT SUBMITTAL ONLY AND DOES NOT INCLUDE MEANS AND METHODS FOR CONSTRUCTION WHICH SHALL BE THE RESPONSIBILITY OF THE 8) ANY NEW ELECTRICAL WORK SHALL COMPLY WITH THE REQUIREMENTS OF THE INTERNATIONAL ELECTRIC CODE, SHALL BE INSTALLED AS INDICATED, AND SHALL BE PROPERLY 9) THE CONTRACTOR (AND SUBCONTRACTORS) SHALL MAINTAIN A CLEAN PROJECT SITE AND SHALL CLEAN UP ALL DEBRIS AND SURPLUS MATERIAL UPON COMPLETION OF THE JOB. 10) THE ARCHITECT WILL NOT HAVE CONTROL OF AND SHALL NOT BE RESPONSIBLE FOR THE CONSTRUCTION MEANS, METHODS, OR PROCEDURES, OR FOR THE SAFETY PRECAUTIONS IN CONNECTION WITH THE WO
1) DO NOT SCALE DRAWINGS. REGULATIONS. RESOLVED. APPROVAL. 5) GENERAL CONTRACTOR AND HIS TO COMPLETE THIS WORK. GENERAL CONTRACTOR. GROUNDED AND SHIELDED. SHEET TITLE G001

| 2220
MECHANICAL CONTRACTOR TO PROVIDE CONCRETE PAD FOR COMPRESSOR MOUNTED AT GRADE
COORDINATE WITH ALL AUDIO/VIDEO, COMPUTER, NETWORK AND SECURITY WHERE INSTALLATIONS THAT
1. CONTRACTOR TO FILL OUT ALL APPLIANCE WARRANTY CARDS AND INFORMATION FOR ALL APPLIANCES
MECHANICAL CONTRACTOR TO PROVIDE PROGRAMMABLE THERMOSTAT (HONEYWELL OR EQUAL).
ELECTRICIAN TO SUPPLY LIGHT FIXTURES WITH SWITCHES (NO PULL CHAINS) AT ALL CLOSETS OF 5 SF OR
ELECTRICAL: PROVIDE ALL MATERIAL AND LABOR TO COMPLETE PROJECT AS PER DRAWINGS AND
WHEREVER STANDARDS HAVE BEEN ESTABLISHED AND THEIR LABEL SERVICE IS REGULARLY FURNISHED.
ELECTRICAL SYSTEM LAYOUTS ARE PER THE DRAWINGS. LOCATION OF OUTLETS AND EQUIPMENT
DUCT TOILET OR BATHROOM EXHAUST TO EXTERIOR PER CODE REQUIREMENTS. EXHAUST DUCT
AS INDICATED ON DRAWINGS AND AS REQUIRED BY CODE PER 2012 IRC R314 AND R315. CONTRACTOR TO
ALL NEW DUCTWORK SHALL BE FABRICATED OF PRIME FIRST QUALITY GALVANIZED SHEET METAL
CONDITIONS AND OBSERVATIONS. WIRING FOR EQUIPMENT REQUIRING MAINTENANCE AND INSPECTIONS
IS APPROXIMATE. EXACT ROUTING OF WIRING LOCATION OF OUTLETS AND EQUIPMENT IS APPROXIMATE.
WATER HEATERS, BATHROOM FANS, DRYER AND COOK TOP HOOD. VERIFY ALL VENT LOCATIONS
AS REQUIRED. ALL CAN LIGHTS BELOW UNHEATED SPACES TO HAVE 'AIR-LOC' GASKETS. ALL CAN LIGHTS
ELECTRICAL EQUIPMENT. PROVIDE AND INSTALL ALL SMOKE, CARBON MONOXIDE AND HEAT DETECTORS
WITH ARCHITECT PRIOR TO INSTALLATION. HVAC CONTRACTOR TO VERIFY ALL NEW DUCT SIZES
CONTRACTOR SHALL PROVIDE ALL LABOR, MATERIALS AND EQUIPMENT NECESSARY TO INSTALL
INSTALL AIR FILTERS AND AIR HANDLERS MUST MAINTAIN ADEQUATE PRESSURE AND AIR FLOW.
WITH CARPENTRY CONTRACTOR PRIOR TO FRAMING. CARPENTRY CONTRACTOR WILL BE RESPONSIBLE
HVAC SYSTEM IS TO BE DESIGNED TO ACCOMODATE THE ADEQUATE AIR CHANGES FOR A TIGHT
FROM WALL. ALL SUPPLY project #
ALL VENTS ARE TO BE COORDINATED WITH ARCHITECT AND THROUGH ROOF IS PREFERRED TO
ARCHITECT. PROVIDE DRIP PAN WITH HIGH WATER ALARM AND FLOOR DRAIN UNDER FURNACE.
U.N.O. GAUGES OF METAL, SPACING ETC. SHALL CONFORM TO THE LATEST EDITION OF ASHRAE
THE FOLLOWING SPECIFICATIONS SHALL GOVERN WITH MODIFICATIONS AS SPECIFIED HEREIN:
CONTRACTOR TO PROVIDE HEAT DURING CONSTRUCTION AS REQUIRED TO PREVENT DAMAGE
ALL CLOSET LIGHTS TO COMPLY WITH N.E.C. MOUNTING AND CONSTRUCTION REQUIREMENTS.
AMERICAN SOCIETY OF HEATING, REFRIGERATION AND AIR CONDITIONING ENGINEERS (AHRAE)
PROVIDE SEPARATE SWITCHES FOR FAN AND LIGHT CONTROL AT BATHROOM FAN/LIGHT UNITS.
ORDINANCES. SUBCONTRACTORS SHALL COORDINATE WORK WITH ALL OTHER TRADES. ELECTRICAL
REGISTERS LOCATED IN HARDWOOD FLOOR TO RECEIVE FLUSH WOOD FLOOR REGISTERS TO
PROVIDE ALL NECESSARY DUCTWORK, FLUES AND VENTS AS REQUIRED FOR FURNACES, HOT
CONTRACTOR TO INSTALL ALL BATH ACCESSORIES. ALL ITEMS SHALL BE INSTALLED IN STRICT
PROVIDE EXTERIOR CLEANOUT IN DISCRETE LOCATION FOR EASY ACCESS AND MAINTENANCE
UPON INSTALLATION, SEAL ALL PERMANENT DUCTS AND VENTS TO MINIMIZE CONTAMINATION
ALL EQUIPMENT INSTALLED OUTDOORS AND EXPOSED TO WEATHER SHALL BE WATERPROOF.
ACCORDANCE WITH THE RESPECTIVE MANUFACTURER'S PUBLISHED INSTRUCTIONS AND APPROVED
MOTORS, HVAC EQUIPMENT, WATER HEATERS, FANS AND CONTROLS. ALL ELECTRICAL WORK SHALL
ENSURE THAT EVERY ROOM (EXCEPT BATHS, KITCHENS, CLOSETS, PANTRIES, AND LAUNDRY
ALL SUPPLY DUCTWORK AT UNCONDITIONED SPACES TO BE INSULATED WITH A MINIMUM R-5
HOME WHICH INCLUDES A ERV OR DEHUMIDIFIER SYSTEM TO PROPERLY CONTROL INDOOR
JOISTS, RAFTERS AND LOAD BEARING STUDS AND RAFTERS ARE NOT TO BE NOTCHED FOR
DEGREES FAHRENHEIT WHEN THE OUTSIDE TEMPERATURE IS TEN DEGREES BELOW ZERO
HEATING SYSTEM SHALL PROVIDE AND MAINTAIN A MINIMUM TEMPERATURE OF SIXTY FIVE
AND LAYOUTS, VENTS, RUNS, FURNACE SIZE, CONDENSING UNIT SIZE AND LOCATION WITH
WIRING, RELATED FIXTURES, ELECTRICAL HEATING ELEMENT AND CONTROLS. ALL WORK SHOULD
CONTRACTOR TO PROVIDE POWER AND FINAL CONNECTIONS AT ALL FIXTURES AND APPLIANCES,
PROVIDE FREEZE PROOF SPIGOT ON EXTERIOR LOCATIONS. SEE DURABILITY STRATEGIES.
PROVIDE TELEVISION CABLE (INDICATED WITH “C”) AS INDICATED ON PLANS; COORDINATE
EXACT ROUTING OF WIRING AND LOCATION OF OUTLETS SHALL BE GOVERNED BY STRUCTURAL
ROOMS) HAS ADEQUATE RETURN AIR FLOW THROUGH THE USE OF MULTIPLE RETURNS,
ELECTRICAL CONTRACTOR TO PROVIDE POWER AND FINAL CONNECTIONS AT ALL HVAC
MATERIALS AND EQUIPMENT SHALL BE NEW AND LISTED BY U.L. AND BEAR THEIR LABEL
APPLIANCE. EXHAUST VENT LENGTH NOT TO EXCEED 25 FT AS CALCULATED PER CODE
AT CLOTHES DRYER TO HAVE SMOOTH INSIDE WITH BACKDRAFT DAMPER. VENT TO BE
FOR ALL REQUIRED RE-FRAMING IF THE BUILT FRAMING CONFLICTS WITH THE LAYOUT OF THE
DURING CONSTRUCTION. REMOVE ANY SEALS AFTER ALL PHASES OF CONSTRUCTION
RELATIVE HUMIDITY TO PREVENT CONDENSATION ON WINDOWS IN BELOW FREEZING
COMPLY WITH THE CURRENT NATIONAL ELECTRIC CODE AND STATE AND LOCAL CODES AND
PROVIDE ALL MATERIALS & LABOR REQUIRED TO COMPLETE PLUMBING WORK.
INSTALLATION DRAWINGS. LOCATION DETERMINED PER ARCHITECTURAL DRAWINGS.
AIR FILTER HOUSINGS MUST BE AIRTIGHT TO PREVENT BYPASS OR LEAKAGE.
ALL ELECTRICAL EQUIPMENT AND BREAKERS SHALL BE PROPERLY LABELED.
MID-DEPTH/WIDTH AS PERMITTED BY CODE AND MANUFACTURER'S INSTRUCTIONS).
2 RATED HOUSING. COORDINATE CAN LIGHT LOCATIONS RIGID METAL. VENT SIZE TO MATCH DIAMETER OF THE
INSTALLATION OF ELECTRICAL CONDUITS (FRAMING MEMBER TO BE DRILLED AT
EQUIPMENT, WATER HEATERS, HARDWIRED APPLIANCES AND EXHAUST FANS.
ALL PORTIONS OF FLOOR SUPPLY REGISTERS TO BE A MAXIMUM OF 9”
PROVIDE GFI OUTLETS AND/OR CIRCUITS PER CODE REQUIREMENTS.
MORE REGARDLESS IF FIXTURE AND SWITCH ARE INDICATED ON DRAWINGS.
CONFIRM TO LATEST EDITION OF THE INTERNATIONAL RESIDENTIAL CODE.
Culp Residence 5308 W 65th PL PRAIRIE VILLAGE, KS 66202 OWNER BRIAN & JENNIFER CULP
CONSTRUCTION STANDARDS FOR DUCTWORK CONSTRUCTION.
PROVIDE DOORBELL BUTTON AND CHIMES PER DRAWINGS.
PROJECT
3 INCLUDING THOSE SUPPLIED BY OWNER. INSTALLED IN INSULATED LOCATIONS TO HAVE IC- ARE OWNER SUPPLIED AND INSTALLED. SHALL BE READILY ACCESSIBLE. PROVIDE SWITCH AT DISPOSAL AS REQUIRED. HANDBOOK OF FUNDAMENTALS. DUE TO TEMPERATURE CHANGES. FAHRENHEIT. INSULATION. IF REQUIRED. MATCH SPECIES OF HARDWOOD FLOOR. CONSTRUCTED WITH MIN. 0.016” REQUIREMENTS. TRANSFER GRILLES, OR JUMP DUCTS. COMPLETED. TEMPERATUTRES. ALL PLUMBING FIXTURES TO BE INSTALLED PER CODE. EXTERIOR WALL CONFIGURATIONS. 8/16/23 Architect David Herron - Kansas License #A-3665
SPECIALTIES 1. 2. APPLIANCES ELECTRICAL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. W/OWNER. 14. MECHANICAL 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. PLUMBING 1. 2. 3. 4. SEAL
THICK AT TUB/SHOWER SURROUND AND WALLS AND CEILINGS
FROM THE CENTER LINE SOLID CORE DOORS FOR
AT ALL BATHROOM WALLS AND CEILINGS NOT RECEIVING CERAMIC
GAUGE THICK FOR
REVISIONS

4 INSTALL FLASHING AND SHEET METAL IN COMPLIANCE WITH “ARCHITECTURAL SHEET METAL BY SMACNA. ALUMINUM FLASHING SHALL CONFORM TO ASTM B 209 AND BE A MINIMUM 0.016” GALVANIZED, STEEL FLASHING SHALL CONFORM TO ASTM A 526, 0.20% COPPER, 26- (0.0179”), ASTM A 525, DESIGNATION G 90 HOT-DIP GALVANIZED, MILL PHOSPHATED. BACKPAINT FLASHING WITH BITUMINOUS PAINT, WHERE EXPECTED TO BE IN CONTACT WITH PROVIDE FLASHING AT ALL ROOF TO WALL CONDITIONS, PROJECTIONS OF WOOD BEAMS THROUGH EXTERIOR WALLS, EXTERIOR OPENING AND ELSEWHERE AS REQUIRED PROVIDING WATERTIGHT/WEATHERPROOF PERFORMANCE. PROVIDE ALL REQUIRED FLASHING, INCLUDING CHIMNEY, VENT, AND OTHER PENETRATION FLASHING AS REQUIRED, AS WELL AS A METAL DRIP EDGE AT ALL ROOF ROOF VALLEY FLASHING SHALL BE PROVIDED NOT LESS THAN NO. 28 GALVANIZED SHEET GAUGE CORROSIVE RESISTANT METAL OR COPPER AND SHALL EXTEND AT A LEAST 11” EACH WAY AND SHALL HAVE THE FLOW LINE FORMED AS PART OF THE FLASHING. SECTIONS OF FIT INSULATION TIGHT WITHIN SPACES AND TIGHT TO AND BEHIND MECHANICAL AND ELECTRICAL PROVIDE INSULATION AS REQUIRED BY CURRENT BUILDING CODE. PROVIDE WATER-RESISTIVE BARRIER AT EXTERIOR WALLS PER 2018 IRC 703.2 PROVIDE SEALANTS AND CAULKING MEETING APPLICABLE SPECIFICATIONS AS REQUIRED TO PROVIDE 6-MIL POLYETHYLENE VAPOR BARRIER MEMBRANE COMPLYING WITH ASTM D-2103 PROVIDE NEW PREFINISHED G

THICK STANDARD BUILDING SHEET OF PLAIN FINISH.
CEMENTITIOUS MATERIALS OR DISSIMILAR METALS.

THERMAL AND MOISTURE PROTECTION

AND WINDOW TRIM EDGES. FLASHING SHALL HAVE AN END LAP OF NOT LESS THAN 4”. SERVICES WITHIN THE PLANE AND INSULATION. LEAVE NO GAPS OR VOIDS. PROVIDE A POSITIVE BARRIER AGAINST MOISTURE AND PASSAGE OF AIR. BELOW BASEMENT SLAB. INSULATE ALL WATER SUPPLY PIPING AS PER CODE. AND EXTERIOR DOORS. 3/16" OR GREATER. BASIS OF DESIGN: KEENE DRIWALL RAINSCREEN 10MM. DOORS AND WINDOWS COMPLETION OF PROJECT. EXTERIOR DOORS TO BE KEYED ALIKE. STAIN. PREMIUM GRADE. SUPPLY AND INSTALL ALL HARDWARE, INCLUDING INCLUDING OWNER SUPPLIED. ALL GLAZING TO MEET 2012 IRC R.308 FOR SAFETY GLAZING. REQUIREMENTS SHALL BE FOLLOWED THE APPLICATION INSTRUCTIONS. GREASE, ASPHALT, RUST, ETC.). WITH AMERICAN STANDARDS SPECIFICATIONS. PROVIDE CEMENT TILE BOARD, ½” “GREENBOARD” PROVIDE ½” PROVIDE ¼” ACCORDANCE WITH MANUFACTURER'S PRINTED INSTRUCTIONS. ENAMEL PAINT FINISH (ONE COAT PRIME, TWO FINISH COATS). VOC WATER BASED SHELLAC. THROUGHOUT DURATION OF CONSTRUCTION. APPROVED BY OWNER AND ARCHITECT PRIOR TO INSTALLATION. DRAWINGS. ALL EXTERIOR TRIM TO BE BACK-PRIMED PRIOR TO INSTALLATION. VERTICAL FIRE CONTAINMENT. DRAWINGS FOR MORE DETAILS. CIVIL ENGINEER Land Survey Company P.O. Box 528 S.W. Corner of 10th & Main Grandview, MO. 64030

MANUAL” AND LABELED. FINISHES SPECIFICATIONS. WALLS, 5/8” ASSEMBLY. FINISH COATS). INSTALLATION.

5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 1. 2. 3. 4. 5. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. TILE. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23.

STRUCTURAL: PROVIDE ALL STEEL, WOOD, AND MANUFACTURED LUMBER MEMBERS PER DRAWINGS.
INCLUDE ALL HARDWARE; INCLUDING SIMPSON JOIST HANGERS, SHEATHING CLIPS, BRACKETS, TIES,
VERIFY LENGTHS AND ELEVATIONS OF ALL LINTELS WITH THE ARCHITECTURAL DRAWINGS. PROVIDE
PROVIDE POSITIVE DRAINAGE AWAY FROM WALL FOUNDATIONS (FINAL GRADE SLOPES AWAY AT 5%
GYPSUM BOARD EACH SIDE DIAMETER
ALL EXPOSED FACES AT CUSTOM MILLWORK TO BE CONSTRUCTED OF SOLID WOOD AND PLYWOOD
ALL SIZES ARE MINIMUM SIZE REQUIRED. MEMBER CAN BE MADE LARGER AS NEEDED W/ARCHITECT
FLATWORK: PROVIDE CONCRETE FLATWORK PER PLANS. PROVIDE CONTROL JOINTS IN SLABS AND
THE USE OF ANY AND ALL DRAWINGS, PLANS, SPECIFICATIONS, ETC., PREPARED BY DAVID HERRON
PROVIDE CUSTOM MILLWORK AS FOLLOWS: WOOD VENEER TO BE SLIP MATCHED, GRADE A MAPLE.
DOUBLE FLOOR JOISTS UNDER ALL INTERIOR PARTITIONS RUNNING PARALLEL TO FLOOR FRAMING
USE PRESSURE TREATED LUMBER WHERE LUMBER IS IN CONTACT WITH CONCRETE OR MASONRY.
(ACI LANDSCAPE ARCHITECT
ALL STEEL SHALL RECEIVE TWO SHOP COATS OF RUST INHIBITIVE GRAY PRIMER, EXCEPT AT SLIP
ALL ARCHITECTURAL CONCRETE SHOULD FOLLOW ACI 301-10, SECTION 6 FOR PROPER FINISHING
THE OWNER/DEVELOPER AGREES TO HOLD ARCHITECT HARMLESS AND DEFEND FROM ANY AND
CARPENTRY CONTRACTOR WILL BE RESPONSIBLE FOR ALL REQUIRED RE-FRAMING IF THE BUILT
ROUGH FRAMING: PROVIDE ALL NECESSARY MATERIAL FOR ROUGH FRAMING INCLUDING WALL,
BEDROOM CLOSET SHELVING: UNLESS NOTED OTHERWISE, ALL BEDROOM CLOSETS TO HAVE A
CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING ALL MEANS NECESSARY TO INSURE THE
FOUNDATION: PROVIDE CONCRETE WALLS AND FOOTINGS, FORMS, STEEL DOWELS, GASKETS,
(ACI 318) AND WITH “SPECIFICATIONS FOR STRUCTURAL CONCRETE FOR BUILDINGS”
GALVANIZED HANGERS FOR ALL PRESSURE TREATED LUMBER.
DIA. U.N.O O.C. WITH ½” PLYWOOD WITH HARDWOOD EDGING OR VENEER BANDING. O.C., TYP. DEPTH, WITH A 1X2 HARDWOOD NOSING, PAINTED. HARDWOOD NOSING
ARISING FROM THE DETECTION, REMOVAL OR DISPOSAL OF ASBESTOS.
GENERAL CONTRACTOR 1741 JEFFERSON STREET
CONSULTANTS FOR THE CONTEMPLATED SERVICES TO THE OWNER.

SOME COMPARABLE APPROACH TO KEEP SOIL STABILIZED.
6 FOR CLARITY NO SERVICES WILL BE PROVIDED WITH REGARD TO THE DETECTION, REMOVAL, DISPOSAL OR STORAGE OF ASBESTOS, AND OTHER HAZARDOUS MATERIALS THAT MAY BE FOUND AT THE PROJECT SITE,. THE OWNER SHALL BE RESPONSIBLE FOR THE DETECTION, REMOVAL AND DISPOSAL OF ALL HAZARDOUS MATERIALS, TOXIC WASTES, ASBESTOS, AND POLLUTANTS AT THE PROJECT SITE IN ACCORDANCE WITH APPLICABLE LAW. IT IS UNDERSTOOD AND AGREED THAT DAVID HERRON AND PARTNERS HAS NO EXPERTISE WITH REGARD TO ASBESTOS AND SHALL HAVE NO RESPONSIBILITY WHATSOEVER FOR OR CONTROL OVER THE DETECTION, REMOVAL OR DISPOSAL OF ASBESTOS. DAVID HERRON AND PARTNERS SHALL HAVE NO RESPONSIBILITY OR CONTROL OVER THE SELECTION OR RETENTION OF ANY EXPERT, CONSULTANT, CONTRACTOR OR SUB-CONTRACTOR ENGAGED IN THE DETECTION, REMOVAL OR DISPOSAL OF ASBESTOS, NOR SHALL DAVID HERRON AND PARTNERS BE RESPONSIBLE IN ANY MANNER TO ANYONE FOR THE ACTS OR OMISSIONS OF ANY PERSON OR ENTITY AND PARTNERS LLC, REMAIN THE PROPERTY OF DAVID HERRON AND PARTNERS LLC, AND SHALL BE RESTRICTED TO THE ORIGINAL SITE FOR WHICH THEY WERE PREPARED. ANY REPRODUCTION OR DISTRIBUTION OF SUCH ITEMS IS EXPRESSLY LIMITED TO SUCH USE. ANY OTHER REPRODUCTION, REUSE OF DISCLOSURE BY ANY METHOD, IN WHOLE OR IN PART, OR FOR ANY OTHER PURPOSE OTHER THAN THAT ALL LOSSES, CLAIMS, LIABILITIES, EXPENSES AND/OR DAMAGES DUE TO OR ARI
AS A CONTRACT DOCUMENT, IS STRICTLY PROHIBITED.

NECESSARY AND PER DRAWINGS. ACI 318 UNLESS NOTED OTHERWISE. CALCIUM CHLORIDE ADMIXTURES ARE NOT PERMITTED. ASTM A36 U.N.O. ASTM A500 FOR STRUCTURAL TUBING (TS);FY=46 KSI PIPE SHAPES TO BE ASTM A53, GRADE B; FY=36 KSI BOLTS AT BOLTED CONNECTIONS TO BE ASTM A325, ¾” AND THE FRAME BECOMES SELF SUPPORTING AND STABLE CRITICAL CONNECTIONS. ANCHOR BOLTS, NAILS AND SCREWS AS REQUIRED. PROVIDE TRIPLE- ALL FRAMING TO BE LEVEL AND PLUMB. SUBCONTRACTOR AND ARCHITECT PRIOR TO FRAMING. HANGERS AS PER DESIGN LOADS. AND BELOW NEW TUBS AND FIREPLACES. EXPOSED SHELVING TO BE ¾” ADJUSTABLE SHELVING TO BE SUPPORTED ON PINS SPACED AT 2” SHELF, RIPPED TO 12” CLOSET ROD (ITEM #257273 OR #257265, LENGTHS AS REQUIRED)

SITE WORK METALS BUILDING CODE” METALS SPECIFICATIONS: CARPENTRY REQUIRED. CONSTRUCTION.” APPROVAL. MILLWORK MATERIALS U.N.O. SINGLE ¾” MECHANICAL ENGINEER

31. 32. 33. 1. MIN.). 2. 1. 2. 3. 4. 5. 6. 7. 8. 1. 2. - - - - - 3. 4. 5. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. LEVEL. 15. 16. 17. U.N.O. 1. 2. 3. 4. 5. 6.

AND FIRE GENERAL PAID FOR BY THE SUBCONTRACTORS ARE RESPONSIBLE PROVIDED PUBLIC RIGHT-OF- CLOSURES DELIVERY
CONSTRUCTION OF THE PROJECT, INCLUDING, BUT NOT LIMITED TO, ALL APPLICABLE STATE
7 TO
CONSTRUCTION ACTIVITIES WITH OWNER TO DISCERN DAYS IN WHICH NO WORK IS TO BE
OWNER PRIOR TO THE INITIATION OF WORK. GENERAL CONTRACTOR IS TO COORDINATE
COMMENCEMENT OF CONSTRUCTION AND BRING DISCREPANCIES IN THE DOCUMENTS
SPECIFIED. THE ARCHITECT MAY BE REFERRED TO AS: DAVID HERRON AND PARTNERS
PERFORMED. HEREIN, THE GENERAL CONTRACTOR MAY BE REFERRED TO AS THE
GENERAL CONTRACTOR TO PREPARE SCHEDULE FOR WORK TO BE APPROVED BY
RESPONSIBILITY OF THE GENERAL CONTRACTOR. THE OWNER WILL PAY FOR THE
FOLLOWING: GENERAL CONTRACTOR, GC OR CONTRACTOR UNLESS OTHERWISE
ALL CODES HAVING JURISDICTION SHALL BE OBSERVED STRICTLY IN THE
A BUILDING PERMIT IS REQUIRED FOR THE PROJECT AND SHALL BE THE

BUILDING PERMITS. GENERAL CONTRACTOR IS TO PAY FOR DUMPSTER PERMITS AS NECESSARY. ALL GENERAL CONTRACTOR TO COORDINATE WITH OWNER FOR PARKING AND STAGING ARRANGEMENTS. IF PUBLIC-RIGHT-OF-WAY IS TO BE CLOSED FOR ANY REASON, THE GENERAL ALL CONTRACTORS SHALL BE LICENSED TO PERFORM WORK WITHIN THE ALL CODES, TRADES STANDARDS AND MANUFACTURERS' INSTRUCTIONS REFERENCED THE SELECTED GENERAL CONTRACTOR SHALL VISIT THE SITE AND CONDUCT A ALL REQUIRED COMMUNICATION SHALL BE THROUGH BOTH THE ARCHITECT AND THE BIDS MUST ACCOMMODATE ALL WORK RELATED TO THE PROPOSED PROJECT AREA, GENERAL CONTRACTOR SHALL REPORT TO THE OWNER AND ARCHITECT ANY DISCREPANCIES WITH THE PLANS AS THEY RELATE TO WORK IN COMPLIANCE WITH ALL LAWS GENERAL CONTRACTOR IS TO PROVIDE ALL WARRANTIES PROVIDED BY GENERAL CONTRACTOR IS TO BE RESPONSIBLE FOR ALL INSPECTIONS AND ALL MANUFACTURER'S PRODUCT SPECIFICATIONS AND/OR WARNINGS FOR PRODUCTS GENERAL CONTRACTOR TO SUBMIT CUT SHEETS FOR FIXTURES, PRODUCTS OR MATERIALS THAT ARE DIFFERENT THAN WHAT WAS SPECIFIED IN THE ORIGINAL DOCUMENTS FOR OWNER AND ARCHITECT APPROVAL PRIOR TO INSTALLATION. SUBSTITUTIONS MAY BE THE CONTRACTOR SHALL MAKE NO STRUCTURAL CHANGES WITHOUT THE WRITTEN NO SMOKING IN ANY INTERIOR SPACES. CONTRACTOR TO PROVIDE AND EXTERIOR ASH SITE PREPARATION: PR

8 NOTES TO BE SUPPLEMENTAL TO PROJECT SPECIFICATIONS. LLC, OR DBA HERRON + PARTNERS. AND LOCAL COUNTY BUILDING, ZONING, ELECTRICAL, MECHANICAL, PLUMBING CODES. THE CONTRACTOR SHALL VERIFY ALL CODE REQUIREMENTS BEFORE THE ATTENTION OF THE ARCHITECT. BUILDING PERMIT. ALL OTHER PERMITS, LICENSES AND BONDS ARE TO BE GENERAL CONTRACTOR OR SUBCONTRACTOR(S). FOR OBTAINING THEIR OWN RESPECTIVE DEMOLITION DEBRIS SHALL BE TAKEN TO A LICENSED LANDFILL WITH PROOF TO THE OWNER. TRASH RECEPTACLES SHALL NOT BLOCK ENTRANCES OR CONTRACTOR IS RESPONSIBLE FOR OBTAINING ANY NECESSARY STREET IN THE CONTRACT DOCUMENTS WILL BE THE LATEST EDITION UTILIZED BY THE PRE-CONSTRUCTION MEETING WITH THE OWNER AND ARCHITECT PRIOR TO THE COMMENCEMENT OF PROJECT WORK. INCLUDING BUT NOT LIMITED TO THE FOLLOWING: MATERIALS, LABOR, ACCESS, SUBCONTRACTORS OR THIRD PARTIES TO THE OWNER AND ARCHITECT. OR MATERIALS, USED IN THE CONSTRUCTION, MUST BE STRICTLY OBSERVED APPROVAL OF THE ARCHITECT OR STRUCTURAL ENGINEER. THROUGHOUT DURATION OF CONSTRUCTION. INCORPORATED THEREIN BY REFERENCE. IMPLY THAT ALL CONDITIONS ARE TREATED SIMILARLY. REGLETS, FLASHING, STRUCTURAL FASTENERS, SLEEVES, ETC. CONDITIONS SHOWN ON DRAWINGS. A DIMENSION NEEDS TO BE VERIFIED COORDINATE WITH ARCHITECT. NOTIFY THE ARCHITECT PRIOR TO THE START OF WORK. PROFILE, DIMENSION AND WHERE APPROPRI

GENERAL NOTES: 1. 2. 3. WAY. 4. PERMITS. 5. MUNICIPALITY. 6. MUNICIPALITY. 7. 8. OWNER. 9. AND TRANSPORTATION. 10. AND STATUTES. 11. 12. APPROVALS. 13. 14. ACCEPTED. 15. 16. CAN. 17. 18. 19. 20. 21. 22. 23. 25. CONSTRUCTION. 26. REQUIRED BY LOCAL STATUTES. 30. SUCH CLAIMS. ARCHITECT OF RECORD herron + partners p.o. box 414986 Kansas City, Missouri 64111 phone: 816.832.4647 www.herronandpartners.com

F E D C B A