Page 19 - Cortech Product Guide No8

LAMINATING

3" Core

®
®
®
1.2 mil SCUFFPROOF MATTE (3" Core) 1.2 mil SCUFFPROOF MATTE ULTRAGRIP (3" Core)
Roll Size 1-6 7-11 12+ Code Roll Size 1-6 7-11 12+ Code
11.75" x 3000' $314.42 $280.97 $247.52 LFSPD.3.1175.03000 11.75" x 3000' $503.26 $449.72 $396.18 LFHSPD.3.1175.03000
12.75" x 3000' $341.19 $304.89 $268.60 LFSPD.3.1275.03000 12.75" x 3000' $546.09 $488.00 $429.90 LFHSPD.3.1275.03000
14" x 3000' $374.60 $334.75 $294.90 LFSPD.3.1400.03000 14" x 3000' $599.61 $535.82 $472.03 LFHSPD.3.1400.03000
18.5" x 3000' $495.03 $442.37 $389.71 LFSPD.3.1850.03000 18.5" x 3000' $792.33 $708.04 $623.75 LFHSPD.3.1850.03000
19.5" x 3000' $521.78 $466.28 $410.77 LFSPD.3.1950.03000 19.5" x 3000' $835.17 $746.32 $657.48 LFHSPD.3.1950.03000
22.5" x 3000' $602.06 $538.01 $473.96 LFSPD.3.2250.03000 22.5" x 3000' $963.64 $861.13 $758.61 LFHSPD.3.2250.03000
24.5" x 3000' $655.56 $585.82 $516.08 LFSPD.3.2450.03000 24.5" x 3000' $1049.30 $937.68 $826.05 LFHSPD.3.2450.03000
27.5" x 3000' $735.83 $657.55 $579.27 LFSPD.3.2750.03000 27.5" x 3000' $1177.80 $1052.50 $927.21 LFHSPD.3.2750.03000

TM
KARESS ROLL LAMINATE

TM
Karess , the multi-sensual laminate, adds a tactile dimension to the allure of print. It feels as delicate as a rose petal
and as luscious as silk. In reality, it is a durable, scuff-resistant ultra-matte laminate that will protect and enhance your
premium prints and packaging products. This OPP film is both an over-laminate and printable. It is also available with
®
an UltraGrip adhesive for digitally printed projects.

HELPFUL HINT: BEST PRACTICES WHEN LAMINATING WITH KARESS FILMS
TM
KARESS LAMINATE IS A THIN, 1.5 MIL OPP BASED FILM.
TM
• To work with thin films, you need to run the supply roll tensions similar or lower than a normal
PET based laminate.
• You can tell if you have too much tension if film is shrinking in width during the heating process.
THE FILM HAS A SILK-FEEL FINISH.
• As a result of the finish, heat doesn’t transfer as well to the film as with a normal matte
or gloss finish.
• You will need to run the temperature at 30 to 40°F hotter than you would a gloss PET film.
An approximate run temperature would be to start at 270°F (135°C) and increase it 10 - 20°F*.
TM
• Due to a slower heat transfer, you may need to run the Karess film slower than a 1.7 mil gloss
PET film to get a good seal.
*As with any film, we recommend doing a lamination seal test on the first sheet out and then again after 25 sheets.
This will tell you if it is stuck to the print.

www.cortechquality.ca 19