Page 68 - ZEST-Binder1 FLIP pdf
P. 68

®
        ben Chalkboard Paint 308

        Surface Preparation                                  Thinning/Clean Up
        Surfaces  must  be  clean,  dry  and  free  of  wax,  grease,  dust,  mildew,   Thinning  is  unnecessary,  but  if  required  to  obtain  desired
        water-soluble  materials  and  scaling  paint.  Hard,  glossy  areas  should   application  properties,  a  small  amount  of  clean  water  may  be
        be dulled with sandpaper to ensure proper adhesion.   added. Never add other paints or solvents. Wash painting tools in
        WARNING! If you scrape, sand or remove old paint, you may release   warm soapy water immediately after use. Spray equipment should
        lead  dust.  LEAD  IS  TOXIC.  EXPOSURE  TO  LEAD  DUST  CAN   be given a final rinse with mineral spirits to prevent rusting or follow
        CAUSE  SERIOUS  ILLNESS,  SUCH  AS  BRAIN  DAMAGE,   state/local guidelines on solvent use.
        ESPECIALLY IN CHILDREN. PREGNANT WOMEN SHOULD ALSO   USE  COMPLETELY  OR  DISPOSE  OF  PROPERLY.  Dry,  empty
        AVOID  EXPOSURE.  Wear  a  NIOSH-approved  respirator  to  control   containers  may  be  recycled  in  a  can  recycling  program.  Local
        lead  exposure.  Carefully  clean  up  with  a  HEPA  vacuum  and  a  wet   disposal   requirements   vary,   consult   your   sanitation
        mop. Before you start, find out how to protect yourself and your family   department  or  state-designated  environmental  agency  on
        by   contacting   the   National   Lead   Information   Hotline   at    disposal options.
        1-800-424-LEAD or log on to www.epa.gov/lead
                                                             Environmental Health & Safety Information
        Primer/Finish Systems
                                                             Use only with adequate ventilation.  Do not breathe spray mist
                                            ®
        Use the appropriate Benjamin Moore  Fresh Start  primer if a primer is   or  sanding  dust.  Ensure  fresh  air  entry  during  application  and
                                  ®
        required.  Follow  label  directions.  For  previously  painted  surfaces  in   drying. Avoid contact with eyes and prolonged or repeated contact
        good  condition,  apply  one  or  two  coats  of  this  product.  Otherwise,   with  skin.  Avoid  exposure  to  dust  and  spray  mist  by  wearing  a
        before  and  after  filling  in  nail  holes,  cracks  and  other  surface   NIOSH approved respirator during application, sanding and clean
                                                     ®
        imperfections, spot prime with the appropriate Benjamin Moore  Fresh   up.  Follow  respirator  manufacturer’s  directions  for  respirator  use.
            ®
        Start   primer.  When  dry,  apply  one  or  two  finish  coats  of  ben ®   Close container after each use. Wash thoroughly after handling.
        Chalkboard Paint (308).
                                                                  WARNING Cancer and Reproductive Harm–
        Application                                          www.P65warnings.ca.gov
        Stir  thoroughly.  Apply  one  or  two  coats.  For  best  results,  use  a
                    ®
        Benjamin  Moore   custom-blended  nylon/polyester  brush,  Benjamin   FIRST AID: In case of eye contact, flush immediately with plenty of
        Moore  short nap roller, or a similar product. This product can also be   water for at least 15 minutes; for skin, wash thoroughly with soap
             ®
        sprayed.  When  brushing  or  rolling,  apply  generously  using  short   and  water.  If  symptoms  persist,  seek  medical  attention.  If  you
        overlapping strokes, always moving from unpainted into painted areas.   experience difficulty breathing, leave the area to obtain fresh air. If
        Do not over apply. Let paint dry before touching up. Do not apply in   continued  difficulty  is  experienced,  get  medical  attention
        temperatures below 50 °F (10 °C).                    immediately.
                                                             IN CASE OF: SPILL – Absorb with inert material and dispose of as
        Before Using                                         specified under “THINNING/CLEAN UP”.
        Allow painted area to cure for a minimum of 3 days before using. Prior
        to initial use, rub entire surface with a piece of white chalk and then   KEEP OUT OF REACH OF CHILDREN
        erase  using  a  clean,  damp  cloth.  Because  of  the  additives  used  in
        some varieties of chalk, which can leave a residue when erased. For   PROTECT FROM FREEZING
        best results, use traditional, non-liquid chalk, in lighter colors.
                                                                Refer to Safety Data Sheet for additional
                                                                      health and safety information































        Benjamin Moore & Co., 101 Paragon Drive, Montvale, NJ 07645 Tel: (201) 573-9600 Fax: (201) 573-9046  www.benjaminmoore.com  M72  308  US  053118
        ben, Benjamin Moore, Fresh Start, Gennex, and the triangle “M” symbol are registered trademarks, licensed to Benjamin Moore & Co.  This product is not
        endorsed by or a division of CHPS.  This product is provided by Benjamin Moore, not CHPS. All other trademarks belong to their respective owners.
        © 2014, 2018 Benjamin Moore & Co. All rights reserved
   63   64   65   66   67   68   69   70   71   72   73