Page 71 - 2018 Racecar Engineering Drag Racing Parts and Accessories Catalog

REAR ENDS & AXLES

GM Axle C-Clips Pinion Yoke Wrench ALL68372
Replacement C-clips for popular GM Wrench fastens to most popular pinion
10- and 12-bolt axles. flanges and companion flanges to hold
Part No. Description when setting bearing pre-load and
ALL66120 7.5" 10-Bolt, 2-Pack tightening retaining bolt or nut. Wrench
ALL66121 8.5" 10-Bolt And 8.875" 12-Bolt, 2-Pack has provisions to work with 1/2" or 3/4"
ALL66122 7.5" 10-Bolt Genuine GM, Each drive tool. Center hole is 2" to clear most
ALL66123 8.5" 10-Bolt And 8.875" 12-Bolt Genuine GM, Each
sockets. Universal slotted bolt patterns
Ford 9" Housing Studs for 1/4", 5/16" and 3/8" fasteners for
ALL72040 most AMC, Dana, Ford and GM yokes.
Studs secure the center section to
the housing and are installed by pull- U-Bolt Kits
ing through with a nut for a press fit. U-bolt kits for 1310, 1330
3/8"-24 threads. Package of 10. and 1350 series U-joints
secure drive-shaft to pinion
Ford 9" Gaskets yoke. Sold in pairs with
ALL72046 nuts and lock washers.
Part No. Description
ALL72044 Paper U-Joint Stud CTC
ALL72045 Thin With Steel Core U-Bolt Series Cap Thread “A” “B”
ALL72046 Thick With Steel Core Std. ALL69015 1310 1-1/16" 5/16"-24 1.750" 1.400"
X-Long ALL69017 1310 1-1/16" 5/16"-24 2.000" 1.400"
Ford 9" Std. ALL69018 1330 1-1/8" 5/16"-24 1.875" 1.575"
Pinion Supports Std. ALL69016 1350 1-3/16" 3/8"-24 2.000" 1.625"
Allstar Ford 9" supports U-Joints
replace original equipment
style cast iron supports. Pro Performance U-joints are greasable and
support is for 35-spline pinion, ALL68390 ALL68395 fit a variety of driveshaft combinations.
Pro Gear-equipped differentials. 1310 Series: 3.218" Wide with 1.062"
Standard “Daytona” support is for 28-spline Caps
pinion gears. All are aluminum and furnished 1330 Series: 3.622" Wide with 1.062" Caps
with races installed. 1350 Series: 3.622" Wide with 1.187" Caps
(Width = B, Caps = A in drawing)
Part No. Description
ALL68390 Pro, 35-Spline, Billet U-Joints With Same Cross Width
ALL68395 Daytona, 28-Spline, Billet Part No. Description
ALL68396 Daytona, 28-Spline, Forged ALL69030 1310 Series
ALL68396
Pinion Seals ALL69031 1330 Series
Replace leaking or damaged seals ALL69032 1350 Series
in most popular differentials. U-Joints With Different Cross Widths
Part No. Description Part No. Description
ALL72146 Ford 9" Standard, 28-Spline, 3" O.D. ALL69034 1310 to 1330
ALL72147 7.5" GM
ALL72148 8.5" GM ALL69035 1310 to 1350
ALL69036 1330 to 1350
Pinion Nuts
Replace original worn or damaged nuts each time Tailshaft Seal And Bushing
a gear set is changed. Nut secures driveshaft yoke The tailshaft bushing is a regular ALL72152
to pinion gear. wear item, located inside the trans-
mission tailshaft housing. It should be
Part No. Description
ALL72155 Ford 8.8" And Standard 9" replaced when replacing the tailshaft
ALL72156 GM 7.5 And 8.5 seal or when a driveshaft failure has occurred.
A worn bushing will cause excessive side-to-
side movement of the slip yoke and create a vibration or leak.
Replacement bushing and seal fits GM Powerglide, Turbo 350,
Ford 9" Pinion Yokes Saginaw, Muncie, Bert and Brinn transmissions.
Forged steel or billet aluminum Allstar Pinion Part No. Description
Yokes are available for Ford 9". ALL72150 Seal
Part No. Description ALL72152 Seal With Bushing
ALL68380 28-Spline Steel Pinion Yoke, Use With 1350 (3-5/8") U-Joint
ALL68382 35-Spline Steel Pinion Yoke, Use With 1350 (3-5/8") U-Joint
ALL68384 28-Spline Aluminum Pinion Yoke, Use With 1310 (3-1/4") U-Joint

69