Page 240 - 2019 Allstar Performance Parts and Equipment Catalog
P. 240

TOOLS & PIT EQUIPMENT


        Toe Plates                                          Ride Height Set-Up Stick ALL10658
        Aluminum plates simplify                            Stick replaces the coil over shock
        setting of toe-in and toe-out.                      and spring assembly during   NEW!
        Plates fit against outside edges             ALL10117  maintenance. Stick has many uses and
        of tires. Using two tape                            may be adjusted to check settings
        measures (sold separately),                         at normal ride height, in race atti-
        measure the distance front                          tude or on the bump stops to
        and rear, between plates.                           evaluate suspension travel.
        The difference in tape                              Adjusts from 15" to 24",
        readings is the toe setting.                ALL10119  measured at the center of rod ends.
        Deluxe plates have radiused
        edges, slots for narrow and wide tape measures and   Set-Up Tool ALL10668
        are 9" tall x 23" wide to work with vehicles with smaller
        wheel openings. Standard plates are 1/2" thick, 11" tall   Tool replaces the front coil-over shock assembly to sim-
        x 32" wide and work well for vehicles with larger wheels   ulate range of front suspension movement for checking
        and wheel openings. Set of two plates.              bump steer and roll center. Hex head threaded shaft
                                                            raises and lowers suspension to simulate racing condi-
        ALL10117 ...... Standard                            tions. Jam nuts can be positioned to limit rebound and
        ALL10119 ...... Deluxe
                                                            compression. Not designed to support total vehicle
                                                            weight, only suspension components.
        16 Ft. Tape Measure
        ALL10675                                            Set-Up Plates
        16' x 3/4" blade has fractional                     Set-up plates are used for
        markings every 1/8" for quick                       squaring and stringing                ALL10660
        reference.                                          chassis to ensure accu-
                                                            rate chassis set-up by
        Toe Gauge ALL10118                                  eliminating wheel and
        Check toe quickly and                               tire differences. Plates
        easily. Allows one person                           are 1/2" thick and can                ALL10662
        operation and the ability                           also be used when setting bump steer or
        to check front and rear                             checking axle tubes for straightness. Sold each.
        toe dimension from the front                        ALL10660 ..... 5x5, 7" x 28"
        of the car without removing tool.                   ALL10662 ..... Wide 5, 12" x 28"
        Adjust stop against front sidewall of
        tires, slide tool to rear sidewall and the difference is the   Set-Up Stand
        amount of toe out. Tool adjusts to measure from 49" to a   Before tire and wheel are removed, measure
        maximum width of 89".                               distance from center of hub to the ground.
                                                            Remove the tire and wheel, replace with the
        Caster Plate ALL10752                               set-up stand and adjust accordingly.
        Not sure if you turned your wheels the              Adjustments can be made with car at
        same amount each time when adjusting                exact ride height with the wheel and
        caster settings on your race car? Unless you        tire out of the way. Sold each.
        have expensive turn plates, you’re never            ALL10664 ..... 5x5
        certain, until now. This quick reference gauge positions   ALL10666 ..... Wide 5
        under the upper ball joint nut, with markings facing up,
        for easy viewing. Place a mark on the shock body or fabri-  Upper Ball Joint Wrench
        cate an indicator to use as a reference point.      ALL11190
                                                            Wrench is designed to
        Ground Clearance Indicator                          remove and install common screw-in upper ball
        ALL10725                                            joints that are 1.900" wide (ALL56214).
        Determine how close the frame is to
        ground on the race track. This unique               Adjustable Panhard Bar Wrench
        kit features an aluminum bracket that               ALL11192
        rivets to the frame with an adjustable 4"           Wrench is designed to
        plastic wear rod.
                                                            work with adjustable Panhard bars with 1-3/8"
        Replacement Part                                    adjusters. Shorter than a standard wrench, this wrench is
        ALL10726 ..... Wear Rods, 4-Pack                    convenient for making adjustments in tight areas.



          238       www.allstarperformance.com
   235   236   237   238   239   240   241   242   243   244   245