Page 31 - LPS Food Grade Approved Products - All Task Solutions 2019

6.3. Methods and material for Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so without
containment and cleaning up risk. Isolate area until gas has dispersed. Eliminate all ignition sources (no smoking, flares, sparks,
or flames in immediate area). Keep combustibles (wood, paper, oil etc) away from spilled material.
This product is miscible in water. Prevent product from entering drains. Absorb in vermiculite, dry
sand or earth and place into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination.
6.4. Reference to other Use personal protection recommended in Section 8 of the SDS. For waste disposal, see section
sections 13.
SECTION 7: Handling and storage
7.1. Precautions for safe Obtain special instructions before use. Do not handle until all safety precautions have been read
handling and understood. Pressurised container: Do not pierce or burn, even after use. Do not use if spray
button is missing or defective. Do not spray on a naked flame or any other incandescent material
Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill,
grind, or expose containers to heat, flame, sparks, or other sources of ignition. All equipment used
when handling the product must be grounded. Do not re-use empty containers. Do not breathe
gas. Avoid contact with eyes, skin, and clothing. Avoid prolonged exposure. Pregnant or
breastfeeding women must not handle this product. Should be handled in closed systems, if
possible. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Avoid
release to the environment. Observe good industrial hygiene practices.
7.2. Conditions for safe Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
storage, including any exceeding 50°C. Do not puncture, incinerate or crush. Do not handle or store near an open flame,
incompatibilities heat or other sources of ignition. This material can accumulate static charge which may cause
spark and become an ignition source. Store away from incompatible materials (see Section 10 of
the SDS).
7.3. Specific end use(s) Not available.

SECTION 8: Exposure controls/personal protection
8.1. Control parameters
Occupational exposure limits
Austria. MAK List, OEL Ordinance (GwV), BGBl. II, no. 184/2001
Components Type Value
2,2-Dimethylbutane (CAS MAK 715 mg/m3
75-83-2)
200 ppm
STEL 2860 mg/m3
800 ppm
2,3-Dimethylbutane (CAS MAK 715 mg/m3
79-29-8)
200 ppm
STEL 2860 mg/m3
800 ppm
2-Methylpentane (CAS MAK 715 mg/m3
107-83-5)
200 ppm
STEL 2860 mg/m3
800 ppm
3-Methylpentane (CAS MAK 715 mg/m3
96-14-0)
200 ppm
STEL 2860 mg/m3
800 ppm
n-Hexane (CAS 110-54-3) MAK 72 mg/m3
20 ppm
STEL 288 mg/m3
80 ppm
Belgium. Exposure Limit Values.
Components Type Value
n-Hexane (CAS 110-54-3) TWA 72 mg/m3
20 ppm
Bulgaria. OELs. Regulation No 13 on protection of workers against risks of exposure to chemical agents at work
Components Type Value
n-Hexane (CAS 110-54-3) TWA 72 mg/m3

Material name: LPS® Food Grade Silicone - ITW Pro Brands (EU) SDS EU
01716 Version #: 02 Revision date: 08-July-2016 Issue date: 02-July-2015 5 / 16