Page 65 - 2018 Alliance Parts Catalog USA Edition
P. 65
SERVICE TIPS (USE IN CASE OF LINK TEST FAILURE)
OMNEX T42: DOWNLOAD ID CODE
Follow these steps to download the transmitter’s unique ID Code into the receiver. This will allow the receiver to establish a
radio link with a specific transmitter. Omnex T42 Download ID Code (Use in case of Link Test failure)
Omnex T42 Download ID Code (Use in case of Link Test failure)
Follow these steps to download the transmitterʼs unique ID Code into the receiver. This will allow the receiver to
NOTE: It is necessary to download the ID code when replacing either the transmitter or the receiver.
Omnex T42 Download ID Code (Use in case of Link Test failure)
Follow these steps to download the transmitterʼs unique ID Code into the receiver. This will allow the receiver to
establish a radio link with a specific transmitter.
Omnex T42 Download ID Code (Use in case of Link Test failure)
establish a radio link with a specific transmitter.
NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the
Follow these steps to download the transmitterʼs unique ID Code into the receiver. This will allow the receiver to
NOTE: It is necessary to download the ID code when replacing either the transmitter or the receiver.
Follow these steps to download the transmitterʼs unique ID Code into the receiver. This will allow the receiver to
establish a radio link with a specific transmitter.
NOTE: It is necessary to download the ID code when replacing either the transmitter or the receiver.
Omnex T42 Download ID Code (Use in case of Link Test failure)
receiver. This will prevent a transmitter from accidentally reprogramming a different receiver in the area.
NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the
establish a radio link with a specific transmitter.
NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the
NOTE: It is necessary to download the ID code when replacing either the transmitter or the receiver.
receiver. This will prevent a transmitter from accidentally reprogramming a different receiver in the area.
Follow these steps to download the transmitterʼs unique ID Code into the receiver. This will allow the receiver to
NOTE: It is necessary to download the ID code when replacing either the transmitter or the receiver.
receiver. This will prevent a transmitter from accidentally reprogramming a different receiver in the area.
establish a radio link with a specific transmitter.
NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the
NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the
receiver. This will prevent a transmitter from accidentally reprogramming a different receiver in the area.
NOTE: It is necessary to download the ID code when replacing either the transmitter or the receiver.
1. Open and Power the R42 receiver. This will prevent a transmitter from accidentally reprogramming a different receiver in the area.
NOTE: When downloading a new ID to a receiver, a safety feature requires that the transmitter be in close proximity to the
Open the lid of the R42 receiver to expose the [Setup] button.
receiver. This will prevent a transmitter from accidentally reprogramming a different receiver in the area.
Supply power the R42 receiver. The (E-Stop) light and the (Link) light will come
on RED and the (Status) light will come on GREEN
A. B.
A. B.
Prepare T42
2. A. Press [E-Stop] A. A. B. B.
B. Twist CW & release [E-Stop] to ensure the A. B. S S
transmitter’s power is OFF. S S
S S
S S
A. B.
A. S B. S
Put T42 into Download Mode
3. A. Press [E-Stop] A. A. B. B.
A. B. S S
B. Press [ON] Switch UP C. D.
S
S
C. S D. S S
C. While holding [ON] Switch, twist the [E-Stop] button clockwise S D.
C.
to release C. D.
S S
D. Release [ON] Switch C. D. S S
S
S
S
S
S
S
S S
4. Put R2160 into Setup Mode A. SETUP SETUP B. SETUP SETUP
B.
A.
NOTE: If left idle in Setup Mode for over 10
seconds, the receiver will time out. The (Link) light A. A. SETUP SETUP B. B. SETUP SETUP
and (Status) light will flash RED rapidly. To return
B.
to Setup Mode, repeat step 4 A. SETUP SETUP
A. Press & hold [Setup] button until (Status) light
goes from slow flash to fast flash (approx.
5 seconds)
B. Release [Setup] button. (Status) light goes to
solid GREEN, (Link) light turns off A. B.
A. B.
A. A. B. B.
5. Download ID Code A. S B.
A. Press [Power] switch UP and
S
release
S
S
B. (Link) light goes to GREEN. Once
complete, (Link) light goes to S
RED as the transmitter turns off
Alliance Concrete Pumps Inc. will not be held liable for any loss, damage, or injury relating to these procedures.
