Page 13 - portfolio

CLIENT
Hook Brick wall Mrs.&Mr. PUJARA
wall 230 mm thk.
10mm ply base on NOTES
4'-3" Sink faucet 1. This drawing is the property and copyright of THE
2" mirror DESIGNER and shall not be copied or used in any way
without their written permission.
2. This drawing shall be read in conjunction with the other
2" 3. It shall be deemed the responsibility of the contractor or
consultants drawings.
8mm Mirror Pasted the fabricator to bring to the notice of the DESIGNER
prior to any construction or fabrication any discrepancy
within or between the aforementioned drawings.
on ply with silicone 4. All dimensions are in mm and to be read only and not
measured.
5. Any discrepancy in the cross check dimensions are to be
Surface Mounted Washbasin brought in the notice of the DESIGNER by the contractor
/ project managers immediately.
1'-6" 2'-1" 1 1 " 2 6. Project managers/contractors to verify all site conditions
and any condition different or not in correlation with the
drawings/details must be immediately informed to the
architects.
9" 1 ADDITIONAL NOTE :-
1. The information in the dwg is to be taken in conjunction
with the specification documents and other documents
1 " that constitute the contract documents in their
2 entirety.any discrepancies or omissions in dimensions,
specifications or alignments must be brought to the
Wooden counter attention of the representative of the architects prior to
implementation. the architects have described their
as per detail intentions and designs, to the best of their ability and
knowledge, in the contract documents.
DETAIL AT A MIRROR FIXING DETAIL 2. Contractor should submit the shop drawings/assembly
detailed drawings for approval to the architect and
COUNTER PLAN client
representative
3. Contractor should submit all the material samples for
consultant's approval prior to start of material
procurement and start of work
4. Contractor should verify the site dimensions prior to
execution
5. Contractor must erect a sample of partitions ,wooden
ceilings ,floorings,wall claddings ,fixtures and fittings
2"
etc.... prior to commencing remainder of the work
6. Contractor ,sub contractor and /or supplier remains
1 1 " 2
responsible for all aspects of safety and security of the
Detail-A product supplied by them as well as drawings submitted
for checking
7. Architect will only be responsible for approving design
intent of shop drawings .no responsibility will be taken
by the architect for structural/electrical/plumbing HVAC
or general safety of the final product
8. PMC should co-ordinate with contractor/ vendors for
timely submission of all above points..
REVISION
border finished in wood 10mm ply Pasted NO. DATE R 2 PARTICULARS
18.02.19
1.
1
1 " thk. on wall with fevicol
2
base on mirror
1
Mirror 4'-2" 1'-11 2" 4'-2" 8mm Mirror Pasted
as per detail
on ply with silicone
2'-1"
1
1'-11 2" 4'-2"
1 1 " 2
2"
MIRROR DETAIL
Sink faucet
2'-1"
DRAWN BY: JIVITESH KAKKAR
CHECKED BY:
Surface Mounted Washbasin DATE: 03.01.2020
Wooden counter
4" PROJECT
Top of counter
MATERIAL PRODUCT MODELNUMBER TRADENAME PRODUCT MATERIAL TRADENAME MODELNUMBER PRODUCT MATERIAL MODELNUMBER TRADENAME
RESIDENCE
1 " 6 1 " 2 1 " Drawer 1 "
1 " 2 2 2 2 INTERIORS AT, S-462
Drawer 6 1 " 2 1 " 2 GREATER KAILASH-II
1'-6 1 " 2 Drawer 1'-7" NEW DELHI
1'-0 1 " 2 1 " 2 DRAWING TITLE
POWDER ROOM 2
1'-2" 2'-1" 1'-2" 2'-6" Drawer
1'-0" VANITY DETAIL
DRAWING NO. :
4'-5"
10" F.F.L AP-GK-IN-
1 " 2
10" INTERIOR DESIGNERS
Floor Finish level perfect
setting
COUNTER ELEVATION COUNTER SECTION *Bottle trap to be adjusted in drawers.