Page 481 - 2018_IRC

CHIMNEYS AND FIREPLACES

FLUE LINER

1 IN. MIN.
H AIRSPACE

ROOF LINE

W
For SI: 1 inch = 25.4 mm.
FIGURE R1003.20
CHIMNEY CRICKET

R1004.3 Decorative shrouds. Decorative shrouds shall not Chimneys for use with open combustion chamber
be installed at the termination of chimneys for factory-built appliances installed in buildings other than dwelling units
fireplaces except where the shrouds are listed and labeled for shall comply with the requirements of UL 103 and shall be
use with the specific factory-built fireplace system and marked “Building Heating Appliance Chimney” or “Resi-
installed in accordance with the manufacturer’s instructions. dential Type and Building Heating Appliance Chimney.”
R1004.4 Unvented gas log heaters. An unvented gas log R1005.4 Factory-built fireplaces. Chimneys for use with
heater shall not be installed in a factory-built fireplace unless factory-built fireplaces shall comply with the requirements of
the fireplace system has been specifically tested, listed and UL 127.
labeled for such use in accordance with UL 127. R1005.5 Support. Where factory-built chimneys are sup-
R1004.5 Gasketed fireplace doors. A gasketed fireplace ported by structural members, such as joists and rafters, those
door shall not be installed on a factory-built fireplace except members shall be designed to support the additional load.
where the fireplace system has been specifically tested, listed R1005.6 Medium-heat appliances. Factory-built chimneys
and labeled for such use in accordance with UL 127. for medium-heat appliances producing flue gases having a
temperature above 1,000°F (538°C), measured at the entrance
to the chimney, shall comply with UL 959.
SECTION R1005
FACTORY-BUILT CHIMNEYS R1005.7 Factory-built chimney offsets. Where a factory-
R1005.1 Listing. Factory-built chimneys shall be listed and built chimney assembly incorporates offsets, no part of the
labeled and shall be installed and terminated in accordance chimney shall be at an angle of more than 30 degrees (0.52
with the manufacturer’s installation instructions. rad) from vertical at any point in the assembly and the chim-
ney assembly shall not include more than four elbows.
R1005.2 Decorative shrouds. Decorative shrouds shall not
be installed at the termination of factory-built chimneys R1005.8 Insulation shield. Where factory-built chimneys
pass through insulated assemblies, an insulation shield con-
except where the shrouds are listed and labeled for use with
the specific factory-built chimney system and installed in structed of steel having a thickness of not less than 0.0187
accordance with the manufacturer’s installation instructions. inch (0.4712 mm) (No. 26 gage) shall be installed to provide
clearance between the chimney and the insulation material.
R1005.3 Solid-fuel appliances. Factory-built chimneys The clearance shall be not less than the clearance to combus-
installed in dwelling units with solid-fuel-burning appliances tibles specified by the chimney manufacturer’s installation
shall comply with the Type HT requirements of UL 103 and instructions. Where chimneys pass through attic space, the
shall be marked “Type HT and “Residential Type and Build- shield shall terminate not less than 2 inches (51 mm) above
ing Heating Appliance Chimney.” the insulation materials and shall be secured in place to pre-
Exception: Chimneys for use with open combustion vent displacement. Insulation shields provided as part of a
chamber fireplaces shall comply with the requirements of listed chimney system shall be installed in accordance with
UL 103 and shall be marked “Residential Type and Build- the manufacturer’s installation instructions.
ing Heating Appliance Chimney.”

456 2018 INTERNATIONAL RESIDENTIAL CODE ®
Copyrighted © 2017 by, or licensed to, ICC (ALL RIGHTS RESERVED); licensed to UL, LLC pursuant to License Agreement with ICC. No further reproductions authorized or distribution authorized.
ANY UNAUTHROIZED REPRODUCTION OR DISTRIBUTION IS A VIOLATION OF THE FEDERAL COPYRIGHT ACT AND THE LICENSE AGREEMENT; AND SUBJECT TO CIVIL AND CRIMINAL PENALTIES THEREUNDER.