Page 54 - 2020 Allstar Performance Parts and Equipment Catalog

CHASSIS Tubing End Caps Remote Starter Button

Shroud Kits
Steel end caps weld to the end or
inside of tubing to provide a clean
look, prevent sharp exposed edges Kit mounts a remote starter button
directly to chassis tubing. Kit includes a
and seal tubes to keep out dirt and shroud to help protect against acci-
debris. Caps are commonly used on dental activation, tab, and starter button. ALL60361
ends of bumpers, to fill existing holes in ALL60360 ..... Welded Kit
frames and as a flat gusset when butt joining ALL60361 ..... Un-welded Kit
sections of square or rectangular tubing. Package of 10.
Part No. Description Thickness Battery Boxes
Round End Caps Universal, lightweight steel bat-
ALL22280 7/8" O.D. .125"
ALL22285 1" O.D. .125" tery boxes may be welded or
ALL22281 1-1/4" O.D. .125" bolted to the frame. Boxes are avail-
ALL22286 1-3/8" O.D. .125" able in two sizes and include hold down hardware.
ALL22282 1-1/2" O.D. .125" ALL76100 ..... Full Size, 12" Wide x 7-1/4" Deep
ALL22283 1-5/8" O.D. .125"
ALL22287 1-11/16" O.D. .125" ALL76101 ..... Short Style, 10" Wide x 7-1/4" Deep
ALL22284 1-3/4" O.D. .125"
Square End Caps Bolt-On Battery Boxes
ALL22290 1" x 1" .085" Battery box has multiple 1/2"
ALL22291 1-1/2" x 1-1/2" .085"
ALL22292 2" x 2" .085" mounting holes to bolt box directly to
the frame rail, inner fender or firewall.
Rectangle End Cap
ALL22294 2" x 3" .085" Box can also be fastened to round tubing
using clamp-on ballast brackets. Constructed ALL76103
Gussets of 13 gauge steel, measures 11" wide x 7" deep
and includes 3/8" battery hold down hardware.
Gussets add support and
strength to tubing joints ALL76102 ..... Clear Zinc
when building roll cages or chassis mounts. Solid, one or ALL76103 ..... Black
three hole gussets are 1-7/8" tall x 1/8" thick.
Stainless Steel Drop-Out
Description 10-Pack 100-Pack
Solid ALL22192 ALL22192-100 Battery Box ALL76105
With One Hole ALL22194 ALL22194-100 The perfect battery box where battery
With Three Holes ALL22196 ALL22196-100 mounts under floor. Eases battery service
and replacement. Box is 10-1/2" wide, 7" deep,
Wrap Around Gussets and 9-1/2" tall and will accept most standard batteries.
Gussets fit 1.50" to 1.75" tubing and
can be used to join tubing from 70° to Ground Stud ALL76147
110°. Wrap around gussets are 1/16" thick
and provide more support and rigidity than Steel ground stud welds to round tubing providing
a standard flat gusset. . a secure location for mounting a negative battery
cable. Weld stud directly to the chassis or create
ALL22199 ............ 10-Pack a secure ground wire location in the foot box or
ALL22199-50 ....... 50-Pack
engine compartment. Stud accepts battery cables
with 3/8" ring terminals.
Rub Rail Flange ALL60023
Flanges are 3/16" thick and commonly Upper Coil-Over
used when building bolt-on style rub rails.
Center hole accepts 1-1/4" tubing and has Shock Mount Kit
two 3/8" mounting holes spaced 2-1/4" ALL60230
apart. Package of 4. Weld-in kit provides a
mounting point for rear
Charging Post Bracket ALL60064 coil-over shock mounts
Securely mount Allstar charging posts on tube, boxed or stock
on vehicles where battery is not easily frames with up to 48"
accessible. Predrilled holes allow quick between frame rails.
mounting to frame or body. Double-D Great for drag racing
hole design positions posts close together, but provides and street applications, kit includes a 48" long, .120" wall
enough room for charging or jumper cable clamps. x 1-1/2" mild steel tube, reinforced mounting tabs, 2" x
Charging posts sold separately. 3" end plates and 1/2" hardware.

52 www.allstarperformance.com