Page 236 - 2018 Allstar Performance Parts and Equipment Catalog
P. 236
TOOLS & PIT EQUIPMENT
Pinion Centering Jig Quick Change Tube
ALL68370 Install/Removal Tool ALL11350
Pinion centering jig fastens to the rear end Finally an easy
housing and locates the pinion centerline when and correct
building or narrowing housings. Machined way to install and remove quick
slots are designed to retain most tape measure change axle tubes. Secure
ends for accurate measurements. Applications support tool into a vice or to
include GM 12 and 14-Bolt, Dana 44 and 60, a workbench with optional
Chrysler 8-3/4", Ford 8.8" and 9" housings. brackets. Components are
included to remove and install
Ford 9" Set Up Carrier tubes with the turn of a
ALL14169 wrench. An adapter for tubes
with Wide 5 or 5 on 5" hubs is
Set up carrier takes the also included.
place of the gear set on
Ford 9" rear end hous- Related Parts
ings and will keep ALL11355 ...... Installation End Cap For
dirt and debris out Bolt-On and 2-7/8" Pin ALL11355
Wide 5 Tubes
of the housing. A ALL11351 ...... Mounting Bracket Kit For
pinion bracket can Quick Change Tube Install/
be attached to Removal Tool ALL11351
the cover so the J-bar or
Panhard bar can be mounted for car transportation. The Axle Spline Tool ALL66104
tip of the handle matches the centerline of the driveshaft Tool clamps in a vise to
U-joint so driveshaft length can be easily measured. Gloss hold 31-spline axles. Assures per-
red powder coated finish. fect alignment for maintenance or
installation of axle plugs used with
Pinion Yoke Wrench Gold-Trac differentials.
ALL68372
Wrench fastens to most popular T-Handle Axle Puller
pinion flanges and companion flanges ALL66115
to hold when setting bearing pre-load All-in-one T-handle puller
and tightening retaining bolt or nut. Wrench has provi- threads into axle for easy instal-
sions to work with 1/2" or 3/4" drive tool. Center hole is lation or removal. Tool includes
2" to clear most sockets. Universal slotted bolt patterns adapters to fit 3/8"-16 coarse
for 1/4", 5/16" and 3/8" fasteners for most AMC, Dana, or 3/8"-24 fine thread solid axles, and 3/4"-16 fine thread
Ford and GM yokes. gun-drilled axles.
Rear End High Pressure Grease ALL78246
Station Brackets Originally used throughout the tool and
ALL10178 die industry, this lube provides
Stand adapter brackets superior durability and wear
fasten to adjustable arms protection taking the place
of most engine stands. of anti-seize in many applications. Recommended for
Supports full size car and spline to spline contact, threaded adjusters and engine
light truck rear axle hous- fasteners. 4 ounce tube.
ings when servicing or Engine Stand
replacing differential gear Not Included Quick Change Oil Plug Sockets
sets. Position housing Six-point sockets fit on a 1/2" drive ratchet
onto arms and secure to remove or install plugs on quick change
into place with included retaining straps. rear ends. Small socket fits plugs in most center ALL11161
sections and side bells. Large socket fits plug in
Spindle Nut Sockets Winters Ford 9" housings. Not recommended for high
Aluminum hex style spindle nut sockets fit torque applications.
1/2" socket wrenches. ALL11160 ...... Small, 1-3/8", Blue Anodized
ALL11161 ...... Large, 1-7/8", Red Anodized
ALL10110 ...... 2-3/8" Spindle Nut Socket For 2" Pin, Allstar, PCR
5x5 And Most Wide 5 Hubs
ALL10115 ...... 2-7/8" Spindle Nut Socket For 2-1/2" Pin, Allstar,
AFCO, Winters And SCP 5x5 Hubs
234 www.allstarperformance.com