Page 20 - portfolio

B CLIENT
1
2 " groove in veneer Mr. Sandeep
i.e. claded over
1 Dahiya
2 " th. plywood
NOTES
1. This drawing is the property and copyright of THE
DESIGNER and shall not be copied or used in any
4'-3" 2. All dimensions are in mm and to be read only and
way without their written permission.
not measured.
3.Project managers/contractors to verify all site
conditions and any condition different or not in
correlation with the drawings/details must be
immediately informed to the architects.
3" 4. The information in the dwg is to be taken in
conjunction with the specification documents and
other documents that constitute the contract
documents in their entirety.
5.It shall be deemed the responsibility of the
contractor or the fabricator to bring to the notice of
the DESIGNER prior to any construction or
4'-0" fabrication any discrepancy within or between the
aforementioned drawings. The designers have
described their intentions and designs, to the best
of their ability and knowledge, in the contract
documents.
6. Contractor should submit the shop drawings/
assembly detailed drawings for approval to the
3" 7. Contractor should submit all the material samples
architect and client representative.
A A' for consultant's approval prior to start of material
procurement and start of work.
1'-10" 8. Contractor must erect a sample of partitions
,wooden ceilings ,floorings,wall claddings ,fixtures
and fittings etc. prior to commencing remainder of
4'-3" 9. Contractor ,sub contractor and /or supplier remains
the work.
responsible for all aspects of safety and security of
the product supplied by them as well as
drawings submitted for checking.
10. Architect will only be responsible for approving
design intent of shop drawings .No responsibility will
4'-6 1 " 2 be taken by the architect for structural/ electrical/
plumbing HVAC or general safety of the final
product.
11. PMC should co-ordinate with contractor/
vendors for timely submission of all above points.
REVISION
NO. DATE PARTICULARS
DETAIL X
B' PLAN
6"
6" 6"
1'-2"
4" 4" 7 1 " 2
2 1 2 " 2 1 2 "

5'-1"

3'-2 2" 1 3'-2 2" 1 3'-2 2" 1 3'-2 2" 1
10'-0" 1'-3"
9'-4 1 " 2 DETAIL X

1'-3" DETAIL Y
5'-5" 5'-6"
1'-3"
G F KEY PLAN
2'-0"
1'-3"
DETAIL Y

SECTION AT B-B' SECTION AT A-A'

DRAWN BY: JIVITESH KAKKAR
CHECKED BY:
DATE: 22.09.19

SE S SW
E W
NE N NW
aluminium batten
1
1
1 2 " X 1 2 " PROJECT
1
2 " groove in veneer 1 4 " th.veneer finishing over RESIDENCE AT
1
plywood with 2 " groove DHANWAPUR
in veneer
1
2 " th. ply is fixed 1
2 " th. ply is fixed
3
3
on 4 " x 4 " allluminium on 4 " x 4 " allluminium
3
3
2'-0" battens in a grid of 2'x2' battens in a grid of 2'x2' DRAWING TITLE
WALL DETAIL
1 1
4 " th.veneer claded over 2 " c-groove in veneer MASTERBEDROOM
1
plywood with 2 " groove as per in elevation (GROUND FLOOR)
inbetween
9 "th. brick wall DRAWING NO. :
9 "thick wall
SD-D-ID-116
aluminium batten DETAIL Y INTERIOR DESIGNERS
1
1
1 2 " X 1 2 "
DETAIL Z
architects I interior designers
gurgaon