Page 15 - Parker - Process filtration

™
Profl ow II General Grade

SPECIFICATIONS
Materials of Construction Performance Attributes Integrity Test Values
Membrane: PTFE Water fl ow rates, Typical* Filter Rating Bubble Point*
Support Layers: Polypropylene
Micron gpm/psid lpm/100mbar Micron psig bar
Structure: Polypropylene
0.05 0.6 3.29 0.05 ≥40 2.8
Effective Filtration Area
0.1 1.2 6.59 0.10 ≥21 1.5
2
2
5.6ft (0.52m ) per 10” (250mm)
0.2 2.5 14 0.20 ≥13 0.9
cartridge
0.45 5.1 28 * In 60/40 IPA/water @ 25°C
Maximum Differential
1.0 6.2 34
Pressure/Temperature
Forward: * Per 10-inch (250mm) cartridge equivalent with
viscosity of 1cP.
80psid (5.5bar) @ 75ºF (24ºC) 10-inch (250mm) Cartridge
40psid (2.8bar) @ 180ºF (82ºC) Water Flow Rate (lpm)
0 4 8 12 16
Reverse: 5
50psid (3.4bar) @ 75ºF (24ºC)
150
Cleanliness (particle shedding) 4 0.05µm
Wet-packed <1 particles/ml >0.2μm 0.10µm
after 6gal @ 1gpm. 3 0.20µm
Data is from open bag and installed, no 100
additional installation fl ushing. Differential Pressure (psid) Differential Pressure (mbar)
TOC/Resistivity Rinse-up 2 0.45µm
(wet-packed) 1.00µm 50
TOC rinse-up to background plus 5 ppb 1
of feed after 70gal@1gpm.
Resistivity rinse-up to background 0 0
minus 0.2 megohm-cm of feed after 0 1 2 3 4 5
30gal@1gpm. Water Flow Rate (gpm)

Ordering Information
Each cartridge is identifi ed with a product number, pore size and lot number for traceability.

3 — 0 — — G

Treatment Styles End Fitting Nominal Length Filter Rating Gasket/O-Rings Gaskets Only
Code Options Code Description Code Description Code Inches mm Code Micron Code Material Thickness
Code
4 Standard 1 No Insert (Std.) 0 DOE (Cuno ® ) 10 10 250 925 0.05 0 Buna-N Inches mm
Flushed Encapsulated 1 DOE 20 20 500 001 0.1 1 EPDM 1 0.200 5
with 18 5 Stainless Steel
6 2 226 | Flat 30 30 750 002 0.2 2 Silicone 2 0.125 3
Megohm
DI Water 6 Encapsulated 3 222 | Flat 40 40 1000 004 0.45 4 Viton ® (1) 0.200 5
Polysulfone 4
6 020 | Internal | Flat 010 1.0 FEP (1) 0.125 3
½˝ Shortened 5* Encapsulated
A 7 226 | Fin
on 222 Fitting Viton ® N No Gasket
8 222 | Fin FEP
120 | Internal | 6* Encapsulated
G
Recessed End cap Silicone
213 | Recessed
H N None
End cap (Ametek)
222/Recessed *O-Rings only
R
End cap
Specifi cations are subject to change without notifi cation. © 2010 Parker-Hannifi n Corporation
For User Responsibility Statement, see www.parker.com/safety domnick hunter Process Filtration - North America
All Rights Reserved
Viton is a registered trademark of E.I. DuPont de Nemours & Co., Inc.
Profl ow is a registered trademark of Parker-Hannifi n Corporation
DS_IP_Profl ow II Rev. A
15