Page 2808 - Flipbook_SolidDesignSoutheast2020

FEATURES OPTIONS

n Ability to blend an exceptionally broad n Liquid injection ports
range of dry bulk materials, emulsions n Polished sanitary construction
and slurries finish to meet USDA, FDA or

I
n nfinitely adjustable rotor speed pharmaceutical requirements
provides low- to high-shear mixing
action to suit each application n Legs and structurals
constructed of carbon steel,

n High throughput with 20 to 30 #304 stainless steel or
seconds residence time typical #316 stainless steel

n Nominal 4-to-1 length-to-diameter n Gear-reduced drives,
ratio for high throughput rates synchronous gear belt reduced
n njection ports allow the addition of drives or a combination of

I
liquids during mixing, and of water and both to optimize speed and
cleaning solutions during wash down high-torque requirements Large-radius ground and polished Model VIM-306-SS Variable-Intensity

n 180° adjustable paddle pitch for n Pillow block bearings for welds connecting paddles to the Continuous Blender constructed of
varying degrees of blending intensity high-temperature or abrasive solid shaft eliminate crevices where stainless steel is equipped with a
n nternal mechanical face seals as applications materials could lodge, allowing rapid high-pressure vessel jacket to ASME

I
standard n Externally-mounted stand- cleaning and sanitizing. For non- code for heating or cooling. Shown
n Multiple “V” belt and sheave drives off bearings with air-purged sanitary applications, the shaft can with 180° adjustable paddles for

n Fully enclosed guards packing gland seals, or block be equipped with 180° adjustable varying degrees of blending intensity.

paddles (right) for varying degrees
Welded paddles (left) for sanitary
n Large, safety-interlocked access doors seals of Teflon or UHMW of blending intensity. service also available. Shown with

for ease of access and maintenance polyethylene in solid and split/ doors removed.
n Complete discharge sanitary designs
I
n Low maintenance n nsulated low-pressure
jackets, and high-pressure
TYPICAL APPLICATIONS jackets constructed to ASME CAPACITIES AND DIMENSIONS
code for heating or cooling
n Dry and moist ingredients n Construction of #304 and High Intensity Continuous Blender Models & Capacities

n Slurries, pastes, emulsions and #316 stainless steel, or MODEL APPROXIMATE OVERALL DIMENSIONS (IN/MM)
sludges AR235 abrasion resistant NUMBER
n Asphalt hot blending steel and exotic materials, Dia (in) x A B C D E F G

(Intake
n Battery materials including additional weld Length (ft) Opening (Discharge
Opening)
hard facing for exceptionally
n Carbon dust abrasive materials
n Coal slurry n Piggyback systems for dual VIM-83 44/1118 28/711 28/711 13/330 7/178 4x4/ 4x6/

n De-dusting fly ash, lime and clays blending requirements such 102x102 102x152
n Fruit slurries as dry blending followed by VIM-124 61/1549 42/1067 36/914 18/457 9/229 6x6/ 6x8/
n Lump breaking liquid additions 152x152 152x203
n Nuclear waste n Control packages
8x8/
8x10/

n Polymer and rubber compounds n Configurations for batch VIM-165 76/1930 52/1321 48/1219 22/559 13/330 203x203 203x254
blending

n Remediation of soils and sewage
liquids VIM-206 94/2388 60/1524 58/1473 28/711 17/432 12x12/ 12x12/
n Shredded vegetables 305x305 305x305
n Tobacco
VIM-306 100/2540 59/1499 64/1626 40/1016 17/432 12x12/ 12x12/
A 305x305 305x305
VIM-368 135/3429 84/2134 72/1829 48/1219 20/508 14x14/ 14x14/
F G 356x356 356x356
B C
E
D
RELATED MUNSON EQUIPMENT: MUNSON MACHINERY CO., INC.
MIXERS: Rotary Batch (high capacity), Ribbon/Paddle/ +1-315-797-0090
Plow, Cylindrical Plow, Vee-Cone, Double-Cone, USA: 1-800-944-6644
Rotary Continuous, Variable Intensity, Fluidized Bed
INFO@MUNSONMACHINERY.COM
SIZE REDUCTION EQUIPMENT: Screen Classifying
©2017 Munson Machinery Co., Inc.
Cutters, Knife Cutters, Pin Mills, Attrition Mills, WWW.MUNSONMACHINERY.COM MUNSON® is a registered trademark BB-0316
Hammer Mills, Lump Breakers, Shredders of Munson Machinery Co., Inc.