Page 501 - Wago_AutomationTechnology_Volume3_2015_US.pdf

6

499

System bus 1: RD+/TD+ Block diagram
Input Output 2: RD--/TD-- Supply
3: TD--/RD-- Digital Input/Output
4: TD+/RD+ X1 ... X2
5: GND M12
M12 B coded Housing: Shield
M12 2
3 Diagnostics sensor/actuator supply 4
MOVILINK ® interface RS-232 RS-485
X3 X4 1: n.c. Tx+/Y 1
2: TxD Tx-/Z Input 0 ... 3
3: n.c. Rx+/A 10 nF 10 nF
4: RxD Rx-/B Logic
5: GND GND
M12 A coded 4/2 Output 0 ...3
Housing: Shield
1: 24 V 270 pF 270 pF
Digital inputs/outputs 3: 0 V U
X1 ... X2 A 5
(two inputs/outputs / connector)
5: n.c. 2
1
4: In-/Output A 270 pF 270 pF
M12 A coded 4
2: In-/Output B
Housing: Shield 3 ® Error
Supply M12 Input/Output MOVILINK F
Interface
270 pF 270 pF 0 ... 3
Input Output 1 + 2
1: 24 V U
2: 24 V U LS
3: 0 V U A
4: 0 V U LS MOVILINK ® Interface
M12 A coded A X3 ... X4 Module mount
Technical Data Technical Data
Digital outputs: System bus: 6
No. of outputs 4 Connection type (3) M12 connectors, B coded, 5 poles,
Connection type (2) M12 connectors, A coded, 5 poles, shielded
shielded Standards and approvals:
Wire connection 2- or 3-wire Conformity marking 1
Output voltage ≤ U A r UL 508
Output current (per channel) 0.5 A (max. 0.6 A), Isolation:
short-circuit/overload proof Channel – Channel no
(thermal disconnection) U LS , U A , system bus 500 V DC each
Voltage drop against U A at 500 mA max. 0.2 V DC Parameterizable functions, MOVILINK interface
®
Output current (module) max. 2 A Operating mode (per module) Easy Modus; Mailbox Modus
Leakage current in OFF state typ. 5 μA Type (per channel) RS-232; RS-485
Output circuit High-side switching Baud rate (per channel) 9,600; 57,600 baud
Information on actuator selection: Parameterizable functions, digital inputs/outputs
Delay time hardware from "0" to "1" Operating mode, input filter, inversion,
(0 – 90%) typ. 90 μs (resistive load) substitute value strategy, manual mode,
Delay time hardware from "1" to "0" online simulation and diagnostics For details, see manual.
(0 – 90%) typ. 310 μs (resistive load) I/O diagnostics:
Rise time from "0" to "1" typ. 60 μs (resistive load) I/O diagnostics (per channel) Overtemperature (DO)
Fall time from "1" to "0" typ. 45 μs (resistive load) I/O diagnostics (per module) Sensor/Actuator supply short-circuit/
Cable length ≤ 30 m overload
Reverse current (in case of recovery for Undervoltage (U LS + U A )
voltages > U A ) ≤ 1 A (error: 1 channel) Process image:
Type of load Inductive, resistive loads and lamps Process data width Interface: 10-byte In/Out data;
Switching frequency Inductive load approx. 20 Hz DIO: 1-byte In/Out data + 1-byte status
Resistive load approx. 500 Hz LED indicators:
Lamp load approx. 500 Hz SB: System bus status LED (green/red/orange)
Parallel connection of 2 outputs for power boost F: Error status LED (red)
for redundant actuation of a load 0 – 3: Signal status, inputs/outputs LED (yellow/red)
Type of protective circuit External protection (e.g., recovery diodes) Ch1.1 + Ch2.1: Transmission status LED (yellow)
Output resistance < 0,4 Ω Ch1.2 + Ch2.2: Reception status LED (yellow/red)
Operating state influence on output: U LS + U A : Supply status LED (green)
PLC CPU stop Acc. to substitute value strategy Indicators Non-latching
Fieldbus disruption Acc. to substitute value strategy
S-bus (system bus) disruption 0 V status
Supply voltage under rated voltage
tolerance 0 V status
Interruption of supply voltage 0 V status
Output operation Non-latching General Specifications
Overload behavior Automatic restart
Dimensions (mm) W x H x L 35.7 x 50 x 117
Weight 260 g