Page 498 - Wago_AutomationTechnology_Volume3_2015_US.pdf

767-5203

6 Serial Interface (RS-232, RS-422/-485)

496 2 interfaces (2xM12) + 4 digital inputs/outputs (2xM12, two inputs/outputs per connector)

SERIAL
Module marking
System bus
output (3)
System bus
input (3)
Ch2.1 Serial interface 2
LED indicators RS-232/
X
Ch1.1 4 RS-422/485
(2)
Serial interface 1 X Ch2.2
RS-232/ 3 Channel marking
RS-422/485 (2 fields for
(2) Ch1.2 2 each port/channel)
X Digital inputs/
0 2 outputs (2),
Digital inputs/ X channel 3 + 4
outputs (2), 3 Channel marking
channel 1 + 2 1 (2 fields for
1 each port
1 field for
24 V each channel)
U U Supply
LS A
Supply 767-5203 output (1)
input (1)

Short description: Included:
The serial interface module controls/monitors devices (e.g., barcode readers, • 1 x WMB marker, orange
printers, scales, laser measurement systems, operator panels, transponders) • 1 x marking strip
and offers in addition digital inputs/outputs. •2 x M12 protective cap

Characteristics:
• 2 serial interfaces (RS-232, RS-422/-485)
• 4 digital inputs/outputs, 24 VDC / 0.5 A
• Diagnostic capable (per channel/per module)
• Parametrizable (serial interface, operating mode, filter, inversion, substitute
value strategy, manual mode, online simulation and diagnostics)

Description Item No. Pack. Technical Data
Unit
Serial Interface (RS-232, RS-422/-485) 767-5203 1 Digital inputs:
Number of inputs 4
Accessories Item No. Connection type (2) M12 connectors, A-coded, 5 poles,
shielded
Marking strips, marking pen, spacer see pages 520 ... 521 Wire connection 2- or 3-wire
module and protective caps Input filter Hardware: ≤ 110 μs
IP67 cables and connectors see pages 502 ... 517 + Section 11 Software: parametrizable
Input characteristic Type 2, acc. to IEC 61131-2
Technical Data Signal voltage (0) -3 V ... +5 V DC
Signal voltage (1) +11 V ... U A DC
Module supply: Input wiring High-side switching
Connection type (1) M12 connectors, A coded, 4 poles; Input voltage 24 VDC (-3 VDC < U IN < +30 VDC);
Derating must be observed Power from U A is strongly recommended,
Current carrying capacity of supply recovery for voltages > U A
connections max. 8 A (U LS : 4 A, U A : 4 A) Input current (typ.) 7.3 mA
Supply voltage Connection of 2-wire BEROs max. 1.5 mA admissible closed current
24 V DC (-25 % ... +30 %) Cable length, unshielded ≤ 30 m
Logic and sensor voltage U LS
24 V DC (-25 % ...+30 %) Wrong connection of inputs No effect
Actuator voltage U A
Supply current Input characteristic:
typ. 75 mA + sensors (max. 400 mA) Input voltage Typical input current
Logic and sensor current I LS
typ. 25 mA + actuators 2.4 A (4 x 600 mA) -3 V < U IN < 0 V 0 mA
Actuator current I A
Protection Reverse voltage protection for U LS + U A 5 V 2.3 mA ... 2.5 mA
Short-circuit protection for sensor/actuator 11 V 6.4 mA ... 6.7 mA
supply 24 V < U A < 31.2 V 7.3 mA ... 7.5 mA
Serial interface:
Interfaces 2
Connection type (2) M12 connectors, A-coded, 5 poles,
shielded
Transmission channels 1 RxD / 1 TxD (full/half duplex)
Type of cable, cable length 15 m (RS-232); 1000 m (RS-422/-485)
Baud rate 300 – 115,200 baud
Buffer 4 KB (In); 4 KB (Out)