Page 468 - 2020-2021 Racecar Engineering Drag Racing Parts and Accessories Catalog

2020 DRAG RACING

Oil Pump Shafts Oil Return Screen Kits
One-piece steel shafts have a pinned Oil return screen kits are engineered to
steel sleeve to maintain cor rect align ment between oil pump and shaft. retain metal fragments in the event of a
Part No. Description valvetrain failure, preventing them from enter-
MOR22070* SB And 90° V6 Chevy ing the oiling system or dropping into the bottom
MOR22077 SB Chevy Dart, .391" Raised Cam end of the engine.
MOR22080 BB Chevy, Except Gen. V, VI
MOR22090* 0.125" Shorter Than Stock To Fit BB Chevy Pumps Used In SB And 90° V6 Part No. Description
MOR22072 BB Chevy Dart, .600" Raised Cam, Blade Drive MOR25000 SB Chevy
MOR22074 BB Chevy, .400" Raised Cam, Hex Drive MOR25001 BB Chevy
MOR22082 BB Chevy, .400" Raised Cam, Blade Drive
*400 C.I. small blocks must be machined to accept these shafts. Shaft opening Engine Magnet Kit
must be enlarged to 9/16" dia.
MOR22710
Typically placed in the lifter valley or dry
Oil Pump Stud Kit
sump tank, magnets are used to attract
MOR38150
metal fragments and minimize damage in the
4130 steel oil pump stud (7/16" x 3-3/16") provides stronger mount ing event of a engine failure. Kit includes (4) each of 1-1/8" OD x
for oil pumps on small block, big block, or 90° V6 Chevy. 3/8" ID and 7/8" OD x 3/8" ID magnets and epoxy.

Main Cap Baffles
Oil Restrictor Kits
Reduce windage and get every last bit Reduce flow to rocker arm assemblies, leaving more
of horsepower with a main cap baffle oil available for rod and main bearings. Power-
between the rear main cap and oil robbing windage is reduced by lessening the volume of oil passing by the
pump. Prevents oil from climbing to the crankshaft during hard launches. rotating assembly on its return to the pan. Not for use with hydraulic lifters.
Part No. Description Part No. Description
MOR23000 SB And 90° V6 Chevy SB And BB Chevys, .0625" Orifice Dia., Screws Into Lifter Gallery Cleaning Plug
MOR23010 BB Chevy MOR22010
Holes At Back Of Block, 2 Per Package
MOR22016 New GM Blocks With Oil Lifter Galley Bosses, Flush With Bellhousing Face, 2 Per Package
Crankshaft Wipers MOR22017 Merlin II Blocks, 2 Per Package
MOR22045 SB Ford 302-351W, 7 Per Package
Designed to remove excess oil from the rotating assembly and reduce MOR22050 Ford 351 Cleveland, Jack Roush Design, 5 Per Package
windage for increased horsepower. Installs between the
oil pan and block. Racing Oil Filters
Part No. Description Filters are rated at 27 microns and provide less pressure
MOR25800 SB Chevy
MOR25830 BB Chevy drop, more flow, less oil by-pass, and maximum oil filtration.
Part No. Description
Louvered Windage Trays MOR22459 Chevy Short Style Oil Filter, 4-9/32" Tall
MOR22460 Chevy Tall Style Oil Filter, 5-1/4" Tall
Windage trays fit Moroso pans to eliminate MOR22461 Chevy Extra Tall Oil Filter, 8" Tall
oil spashback from the rotating assembly. MOR22462 Chevy Gen. III, 1997-06 GM LS, 13/16"-16 UNF Thread, 3-1/2" Tall
Trays direct oil to the sump. MOR22463 Ford 4.6L/GM LS, 2007-Up, 22mm-1.5 Thread, 3-1/2" Tall
MOR22470 Ford/Chrysler Tall Style Oil Filter, 5-1/4" Tall
Part No. Description
MOR22933 Ford Modular 4.6/5.4L “Engine Saver” Pre-Filter Screen
MOR22935 SB Ford 351W, Rear Sump Pan
MOR23845
MOR22940 BB Ford 352-428 “FE” Stainless steel screen fits at the top of spin-on oil filters to
MOR22941 GM LS, Mounts To Main Caps
MOR23020 SB Chevy, Use Kit MOR38210 For 2-Bolt Main Or MOR38230 For 4-Bolt Main Mounting trap debris before it enters the filter element. Serves as an “early warning
MOR23030 BB Chevy, Use Kit MOR38260 For 2-Bolt Main Or MOR38280 For 4-Bolt Main Mounting signal” during filter inspection. Fits all small and big block Chevy engines
MOR23210 Toyota 3TC, 2T And 2TC with spin-on oil filters.

Windage Tray Screen External Heating Pads
MOR22912 Pads adhere to dry sump oil tanks or oil pans to
Unidirectional screen prevents oil splashback to pre heat oil. Etched foil dis trib utes heat evenly and
increase horsepower. Screen is 23" x 16" and may silicone outer shell resists oil and dirt. Includes 8",
be trimmed to fit most engines. 18-AWG elec tri cal cord with plug for 110-volt AC outlets. MOR23996
Part No. Description
MOR23995 6" x 12" Pad, 360 Watts, Hook And Spring Attachment
MOR23996 5" x 7" Pad, 400 Watts, Heats Oil From 66°F To 160°F In 25 Min.
MOR23997 2" x 15" Pad, 150 Watts, Perfect For Narrow Areas

467