Page 71 - 2020-2021 Racecar Engineering Drag Racing Parts and Accessories Catalog

2020 DRAG RACING

Rear Ends & Axles

GM Axle C-Clips U-Bolt Kits
Replacement C-clips for popular GM 10- and 12-bolt axles. U-bolt kits for 1310, 1330, and 1350 series
Part No. Description U-joints secure drive-shaft to pinion yoke. Sold in
ALL66120 7.5" 10-Bolt, 2-Pack pairs with nuts and lock washers.
ALL66121 8.5" 10-Bolt And 8.875" 12-Bolt, 2-Pack
ALL66122 7.5" 10-Bolt Genuine GM, Each U-Bolt U-Joint Cap Thread “A” Stud CTC
“B”
Series
ALL66123 8.5" 10-Bolt And 8.875" 12-Bolt Genuine GM, Each
Std. ALL69015 1310 1-1/16" 5/16"-24 1.750" 1.400"
X-Long ALL69017 1310 1-1/16" 5/16"-24 2.000" 1.400"
Ford 9" Housing Studs Std. ALL69018 1330 1-1/8" 5/16"-24 1.875" 1.575"
ALL72040 Std. ALL69016 1350 1-3/16" 3/8"-24 2.000" 1.625"
Studs secure the center section to the hous-
ing and are installed by pulling through with U-Joints
a nut for a press fit. 3/8"-24 threads. Package of 10. Performance U-joints are greasable and fit a
variety of driveshaft combinations.
Ford 9" Gaskets 1310 Series: 3.218" Wide with 1.062" Caps
1330 Series: 3.622" Wide with 1.062" Caps
Part No. Description
ALL72044 Paper 1350 Series: 3.622" Wide with 1.187" Caps
ALL72045 Thin With Steel Core (Width = B, Caps = A in drawing)
ALL72046 Thick With Steel Core
ALL72046
U-Joints With Same Cross Width
Ford 9" Pinion Support
ALL68396 Part No. Description
ALL69030 1310 Series
Allstar forged aluminumFord 9" support replaces original equipment cast ALL69031 1330 Series
iron supports. This standard “Daytona” support for 28-spline ALL69032 1350 Series
pinion gears, is furnished with races installed.
Part No. Description U-Joints With Different Cross Widths
ALL68390 Pro, 35-Spline, Billet Part No. Description
ALL68395 Daytona, 28-Spline, Billet ALL69034 1310 to 1330
ALL68396 Daytona, 28-Spline, Forged ALL69035 1310 to 1350
ALL69036 1330 to 1350
Pinion Seals
Replace leaking or damaged seals in most popular differentials. Ford 9" U-Joint Girdle Kit
ALL69025
Part No. Description
ALL72146 Ford 9" Standard, 28-Spline, 3" O.D. Aluminum U-joint girdles NEW!
ALL72147 7.5" GM replace standard steel U-bolts and provide more
ALL72148 8.5" GM
surface clamping area for 1310 and 1330 (1-1/16”) U-joint caps. Girdle
Pinion Nuts design helps prevent over-tightening and includes mounting hardware.
Replace original worn or damaged nuts each time a gear set
is changed. Nut secures driveshaft yoke to pinion gear. GM U-Joint Strap Kit
ALL69014
Part No. Description NEW!
ALL72155 Ford 8.8" And Standard 9" Replacement O.E. style U-joint strap
ALL72156 GM 7.5 And 8.5 kit fits popular GM pinion yokes including 7.5", 8.2", 8.5"
10-bolt and other popular rear ends. Kit is designed for 1-1/8" (1.125")
Ford 9" Pinion Yokes
diameter caps and includes (2) 5/8" wide steel straps with 1-7/8" CTC
Forged steel or billet aluminum Allstar pinion yokes holes and (4) 1-1/2" long 5/16"-24 grade eight bolts.
are available for Ford 9".
Part No. Description Tailshaft Seal And Bushing
ALL68380 28-Spline Steel Pinion Yoke, Use With 1350 (3-5/8") U-Joint
ALL68382 35-Spline Steel Pinion Yoke, Use With 1350 (3-5/8") U-Joint The tailshaft bushing is a regular wear item, located
ALL68384 28-Spline Aluminum Pinion Yoke, Use With 1310 (3-1/4") U-Joint inside the transmission tailshaft housing. It should be replaced
when replacing the tailshaft seal or when a driveshaft failure has ALL72152
Pinion Yoke Wrench occurred. A worn bushing will cause excessive side-to-side movement of the
ALL68372
slip yoke and create a vibration or leak. Replacement bushing and seal fits GM
Fastens to most pinion/companion flanges when setting Powerglide, Turbo 350, Saginaw, Muncie, Bert, and Brinn transmissions.
bearing pre-load or tightening pinion bolt/nut. Wrench Part No. Description
has provisions for 1/2" or 3/4" drive. Bolt patterns for 1/4", 5/16", and ALL72150 Seal
3/8" fasteners for most AMC, Dana, Ford, and GM yokes. ALL72152 Seal With Bushing

70