Page 384 - 2018 Racecar Engineering Drag Racing Parts and Accessories Catalog

Safety Bellhousings Pilot Bearings/Bushings
One-piece bellhousings are hydroformed Eases shifting. Should be replaced any time the
from 1/4" thick steel and tested to meet or clutch assembly is replaced.
exceed SFI standards. Complete with block Part No. Description
plate (except LWI15120 and LWI15220). LWI15975 Chevy V8 Roller Pilot Bearing, Adapts Ford Or Lenco Trans. To Chevy Engine
NHRA/IHRA mandated on any drag car LWI15976 Chevy V8 Bronze Pilot Bushing, OEM-Style Replacement
Chevy V8 Roller Pilot Bearing,
quicker than 11.49 E.T. LWI15977 Reduces Parasitic Drag, Improves Performance
Part No. Description
LWI15000 Chevy V8 And 90° V6, 1958-81
Camaro/Firebird, 1984-92 SB/V6 Chevy, B-W T-5,
LWI15020
T-10 Or Muncie Transmission Heavy Duty Clutch Forks
Chevy II/Nova, 1964-67 V8, Accepts Muncie/Saginaw/B-W T-10,
LWI15050 Heavy gauge steel clutch forks are
Use With Mech. Linkage
LWI15100 Olds And Pontiac V8, 1965-77 engineered specifically for Lakewood
LWI15200 Ford 289-302-351W&C All 6-Bolt Blocks, 1965-78, Use 184-Tooth Flywheel safety bellhousings. Recommended
LWI15335 BB Mopar, 1959-78, Accepts 1975-89 New Process A-833 4-speed when installing a high performance clutch.
LWI15705 Replacement Chevy Block Plate
Part No. Description
LWI15500 Heavy Duty Clutch Fork, Most GM Applications
Transmission Adapter LWI77-150 LWI15510 Fork Pivot Boot, All Chevy/Lakewood Bellhousing Apps.
One-piece steel bellhousing, which fits LWI15525 Custom Clutch Fork, 1979-85 Ford Mustang 5.0L, Long-Style Clutch
all 1958-81 Chevy V8 and 90° V6 with LWI15535 Custom Clutch Fork, 1979-85 Ford Mustang 5.0L, Diaphram Style Clutch
block mounted starter, is perfect for
street/strip or mild drag race applications
where SFI-approved bellhousings are not
required. Block plate not included. GM And Ford Mustang
Clutch Fork Pivot Balls
Bellhousing Locating Kit Adjust clutch fork height and prevent clutch
Misaligned bellhousing register bores release problems. Recommended for Lake-
cause missed shifts and premature pilot wood safety bellhousings.
bearing failure. Lakewood’s centerless ground dowels replace Part No. Description
the stock pins after the bellhousing dowel pin holes have been LWI15501 Most GM Applications
enlarged by approximately 1/16". After the bellhousing is loosely LWI15503 1979-02 Ford Mustang, 2.317" Long, 1/2"-13
installed, the register bore is checked using a dial indicator and LWI15504 1979-02 Ford Mustang, 2.645" Long, 1/2"-13
the bellhousing is located in the proper position. Chamfered
washers are then slipped over the dowel pins and welded in place
to complete the installation.
“Muscle Mounts” For Small Block Ford
Part No. Description
LWI15980 Ford/Chrysler, .500" Dia. LWI24094
LWI15981 GM, .622" Dia. Motor mounts use heavy gauge steel
brackets with hard durometer rubber for
rigid engine placement without the noise
EZ-Adjustable Bellhousing Dowel Pins and vibration associated with solid steel
New EZ-Adjustable dowel pins install into the mounts. Fit most small block Ford 289,
engine block without pounding and may be 302, 351C and 351W including 1966-72 Ford Mustang,
turned with a screwdriver. Once the dowels are 1966-71 Ford Fairlane/Torino, 1966-71 Mercury Comet/Montego
installed in the desired position, a set screw is and 1968-72 Mercury Cougar. Sold each.
tightened to prevent turning.
.007" .014" Driveshaft Loops
Application Offset Offset Prevents driveshaft
GM, .621" Dia. LWI15907 LWI15914
from entering the driver
compartment in the
Offset Dowel Pins event of driveshaft or
Adjustable dowel pins correct improper alignment of U-joint failure. Con-
bellhousing to engine block. structed of 2" x 1/4"
.000" .007" .014" .021" thick zinc-plated steel.
Application Offset Offset Offset Offset Required by NHRA/IHRA for quicker than 14.00 cars equipped
GM .625" Dia. LWI15915 LWI15920 LWI15930 LWI15940 with slicks.
Ford/Chrysler .500" Dia. LWI15945 LWI15950 LWI15960 LWI15970
Part No. Description
LWI18000 Universal Fit
LWI18017 Custom Fit For 1979-03 Mustang
LWI18020 Custom Fit For 1982-92 Camaro/Firebird

382