Page 481 - Wago_AutomationTechnology_Volume3_2015_US.pdf

6

479

System bus 1: RD+/TD+
Input Output 2: RD--/TD-- Block diagram of an input/output
3: TD--/RD--
4: TD+/RD+
5: GND Digital Input/Output Supply
Housing: Shield X1 ... X4
M12, B coded
M12 M12
2
3 Diagnostics sensor/actuator supply 4
Digital Inputs/Outputs
X1 ... X4 1: 24 V
1
(two channels per connector) 3: 0 V U A
Input 0 ... 7
10 nF 10 nF
Logic
Output 0 ...7
4/2
M12, A coded
4: In-/Output A
2: In-/Output B
Input/Output Error
0 ... 7 F
Supply 1: 24 V U 10 nF 270 pF
Input Output 2: 24 V U LS
A
3: 0 V U LS
4: 0 V U
A
Module
mount
M12, A coded
Technical Data Technical Data
Digital outputs: Counters: 6
No. of outputs 8 No. of counters 2
Connection type (2) M12 connectors, A coded, 4 poles Counter type Event/Gate time counter, pulse duration
Wire connection 2- or 3-wire Counting/switching frequency 0 Hz ... 1 kHz
Output voltage ≤ U A System bus:
Output current (per channel) 0.5 A (max. 0.6 A), Connection type (3) M12 connectors, B coded, 5 poles,
short-circuit/overload proof shielded
(thermal disconnection) Standards and approvals:
Voltage drop against U A at 500 mA max. 0.2 V DC Conformity marking 1
Output current (module) max. 4 A Korea Certification
Leakage current in OFF state typ. 5 μA r UL 508
Output circuit High-side switching Isolation:
Information on actuator selection: Channel – Channel no
Delay time hardware from "0" to "1" U LS , U A , system bus 500 V DC each
(0 – 90%) typ. 90 μs (resistive load) Configurable functions:
Delay time hardware from "1" to "0" Operating mode (per module) DO-Module/DI-Module/DIO-Module/
(0 – 90%) typ. 310 μs (resistive load) DIO + 1 counter/DIO + 2 counters
Rise time from "0" to "1" typ. 60 μs (resistive load) Input filter (per channel) 0.1/ 0.5/ 3 /15 /20 ms/ filter off
Fall time from "1" to "0" typ. 45 μs (resistive load) Inversion (per channel) On/off
Cable length, unshielded ≤ 30 m Substitute value strategy (per channel) Switch substitute value/hold last value
Reverse current (in case of recovery for Substitute value (per channel) 0/1
voltages > U A ) ≤ 0,5 A (error: 1 channel) Manual mode (per channel) On/off
Type of load Inductive, resistive loads and lamps Manual mode value (per channel) 0/1
Switching frequency Inductive load approx. 20 Hz Online simulation (per channel) Lock/unlock; simulation value: 0/1
Resistive load approx. 500 Hz Online simulation (per channel/module) Diagnostics
Lamp load approx. 500 Hz I/O diagnostics:
Parallel connection of 2 outputs for power boost I/O diagnostics (per channel) Overtemperature
for redundant actuation of a load I/O diagnostics (per module) Sensor/Actuator supply short-circuit/
Type of protective circuit External protection (e.g., recovery diodes) overload; Undervoltage (U LS + U A )
Output resistance < 0.4 Ω Process image:
Operating state influence on output: Process data width Depends on operating mode
PLC CPU stop Acc. to substitute value strategy LED indicators:
Fieldbus disruption Acc. to substitute value strategy SB: System bus status LED (green/red/orange)
S-bus (system bus) disruption 0 V status F: Error status LED (red)
Supply voltage under rated voltage 0 ... 7: Input and output signal status LED (yellow)
tolerance 0 V status 0 ... 7: Output diagnostics LED (red)
Interruption of supply voltage 0 V status U LS + U A : Supply status LED (green)
Output operation Non-latching Indicators Non-latching
Overload behavior Automatic restart General Specifications

Dimensions (mm) W x H x L 50 x 35.7 x 117
Weight 255 g